User manual STRONG SRT 55

[. . . ] PART 1 · English TABLE OF CONTENTS 1. 0 INSTRUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2. 0 CONNECTION 3. 0 YOUR RECEIVER 3. 1 Remote Control 4. 0 FIRST TIME INSTALLATION 5. 0 MAIN MENU 5. 1 Channel 5. 2 Installation 5. 3 Setup 5. 4 Tools 5. 5 Media+ 6. 0 OPERATION 6. 1 Changing Channels 6. 2 Accessing the Electronic Program Guide (EPG) 6. 3 Accessing the favourite channels A. 1 TROUBLESHOOTING A. 2 SPECIFICATIONS 2 2 3 3 4 5 5 6 6 6 7 8 9 11 12 14 14 15 15 15 16 English 1 PART 1 · English 1. 0 INSTRUCTION 1. 1 Safety Instructions This SCART Receiver has been manufactured to satisfy international safety standards. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerous voltage with the inside of the product that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. Read All Instructions - Before you use the product, read all operation instructions, For more information on accessories such as the lithium ion battery, refer to the manuals provided with those products. [. . . ] Use the tu buttons to select one of two Scan Modes ­ By Channel and By Frequency. When By Channel is selected use the cursor buttons to select Scan Band and Channel No. When By Frequency is selected use the cursor buttons to select Frequency and Bandwidth. Select Network Search to ON or OFF, highlight Search and press OK to start scan. After Channels are found, they will be stored and receiver switches to the first one saved in the list. 5. 2. 3 Antenna Setting 1. Use the pq buttons to select Installation, press OK to enter the menu. If On is selected, the receiver will provide 5 V antenna power (for active antennas). Press EXIT button to exit. 5. 2. 4 Logical channel numbering If LCN (Logical Channel Number) is activated and LCN signal is provided by operator, then channels will be stored at operator defined order. You can activate/deactivate the LCN function by setting the "LCN Mode" to ON/OFF. 5. 3 Setup This menu allows you to set OSD Language, TV System, Region and Time, Timer Setting, OSD Setting and Parental Lock. Press pq buttons to highlight desired menu and press OK button to enter the setting menus. Now you can select desired setting by pq buttons and confirm it with OK. Press EXIT button to exit. 5. 3. 1 OSD Language 5. 3. 2 TV System This menu allows you to set OSD Language. Display Mode: PAL/NTSC/AUTO Aspect Ratio: Use this menu to configure the screen aspect between: 4:3 PS (Pan&Scan), 4:3 LB (Letter Box) and 16:9 (Wide Screen) and AUTO Video Output: Switch the video output mode either to RGB or to CVBS 9 English PART 1 · English 5. 3. 3 Region and Time Here you can set your region and time zone. The options are: Off / User Define / By Region GMT Offset: This menu is valid only when selected "User Define" in GMT Usage menu. The GMT offset range is "-11:30 ~ +12:00", increasing by half hours progressively. Date/Time: "Date" and "Time" menus are valid only when selected "Off" in GMT Usage menu. Time Display: This menu allow to control whether the time is displayed on screen or not. The options are: Off/On. 5. 3. 4 Timer Setting In this menu you can set a programme timer or sleep timer. Programme timer Timer Number: You can set 8 timers Timer Mode: Off/Once/Daily/Weekly/Monthly Timer Service: TV Service/Radio Service Wake-up Channel: You can select a desired channel as wake-up channel. Month/Date/Day: Press pq buttons to select your desired month, date and day. Duration: Press OK to input desired duration with the numeric buttons. Auto Record: Use the tu buttons to adjust On or Off, depending if you want Timer to activate recording via SD Card. [. . . ] Insert the time with the Numeric buttons and press OK to confirm then press EXIT to remove the message. From EPG Press the EPG button to enter the programme guide, than select an event and channel with the buttons described on screen. If you want to remove the planned record you have to press button again. Manual scheduling If you want to set a record manually you can set recording through the Timer menu. [. . . ]