User manual STRONG SRT 6365 PDR

[. . . ] Digital Satellite Receiver with Digital Recorder SRT 6365 PDR User Manual Picture similar PART 1 · English TABLE OF CONTENTS 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2. 0 YOUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control Unit 3. 0 CONNECTIONS 3. 1 Connecting to TV & VCR 3. 2 Connecting to Digital Audio Amplifier 3. 3 Connecting to Satellite Dish 3. 4 Connecting to computer via serial cable for downloading software 4. 0 STARTING UP FOR THE FIRST TIME 4. 1 Language Selection 4. 2 Select connection type 4. 3 Select Satellite 5. 0 MAIN MENU 5. 1 Channel Organiser 5. 2 Installation 5. 3 Timer 5. 4 Games 5. 5 Common Interface 6. 0 RECORDER 6. 1 Records Organiser 6. 2 HDD Information 6. 3 HDD Format 6. 4 Recorder Settings 7. 0 WATCHING TV AND LISTENING TO THE RADIO 7. 1 Program Guide (EPG) 7. 2 Zapping and information banners 7. 3 Channel list 7. 4 Selection of Audio Language 7. 5 TELETEXT function 7. 6 Subtitles function 8. 0 RECORDING AND PLAYBACK 8. 1 Start a record 8. 2 Stop a record 8. 3 TimeShift and Instant recoding 8. 4 Playback A. 1 TROUBLESHOOTING A. 2 SPECIFICATIONS A. 3 TYPICAL INSTALLATIONS AND CONFIGURATIONS 2 2 2 3 3 5 5 5 6 7 7 8 8 9 9 9 9 10 11 11 12 17 18 18 19 19 20 20 21 21 21 21 22 22 22 22 22 22 23 23 24 26 26 28 1 English PART 1 · English 1. 0 INTRODUCTION 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: n In a closed or poorly ventilated cabinet; directly on top of or under any another equipment; on a surface which might obstruct the ventilation slots. DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: n To direct sunlight or near any other equipment that generates heat; to rain or intense moisture; to intense vibration or to any shock which may cause permanent damage to your receiver or to any magnetic objects, such as loudspeakers, transformers, etc. It is dangerous to touch the inside of the receiver due to high voltage, currents and possible electrical hazards. n When the receiver is not used for a long period of time, you should switch OFF the receiver (Power Switch) and unplug the power cord from the wall socket. [. . . ] Once you are sure that dish is fine adjusted press YELLOW (Store) or BLUE (Store&Exit) button. 5. 2. 2 Dish set-up In this menu you can setup parameters of your dish(es). This number used in Channel setup menu to create a link between satellite and corresponded dish configuration. It is advisable to not change this value in case you have installed channels. Before change the value please careful read chapter 3. 3 of this manual. Tuner: This option is available to select in case if Connection type is "Separated". Use tu buttons to select tuner number which corresponds to the selected dish number. If you set type to "CUSTOM" then you should enter values of Local Oscillator Frequencies in LO frequencies menu item. LO frequencies: This menu item selectable only in case LNB type is "CUSTOM". Press OK button and using Numeric buttons enter values in appeared dialog box. Set to Auto in order receiver automatically select band by sending 22 kHz control signal. Set to ON in order receiver generate 22 kHz control signal continuously, or set to OFF in order to disable 22 kHz control signal. Set to 13V or 18V in order receiver supply LNB with selected power, or set to OFF in order to disable LNB power. Dish mode: Use tu buttons to select mode between Fixed, DiSEqC 1. 2 and GOTO X. 5. 2. 3 Edit satellites In this menu you can edit satellite's name, angle, location and transponder, as well as add new satellite. Edit existing satellite and add new satellite functions are identical. Press RED button to save new name or press GREEN button to discard changes. Angle: Use Numeric buttons to enter value of orbital position of the satellite. Location: Use tu buttons to select East or West location of the satellite. Transponder table: Press OK button to enter to edit transponder table menu. In this menu use RED button to edit parameters of selected transponder, GREEN button to add new transponder or YELLOW to delete selected transponder. 15 English PART 1 · English To save changes press the YELLOW (Save) or BLUE (Save & Exit) button. [. . . ] To jump between bookmarks: start playback of selected record, press INFO and press & button. If you wish to continue from another bookmark then press & again. 25 English 8. 4. 7 Place a bookmark This function allows you to place a bookmark at the most interesting moments of a record. Use tu buttons to scroll in the record to the point where you want to place a bookmark and press & button. You can place up to 32 bookmarks in one record. PART 1 · English A. 1 TROUBLESHOOTING There may be various reasons for the abnormal operation of the receiver. [. . . ]