User manual STRONG SRT 6511

[. . . ] Digital Satellite Receiver SRT 6511 User Manual Picture similar PART 1 · English TAblE of ConTEnTs 1. 0 InTRoDUCTIon 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2. 0 YoUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control Unit (RCU) 3. 0 ConnECTIons 3. 1 Connecting to TV & VCR 3. 2 Connecting to Digital Audio Amplifier 3. 3 Connecting to Satellite Dish 3. 4 Connecting to computer by serial cable 4. 0 sTARTIng UP foR ThE fIRsT TImE 4. 1 Language Selection 4. 2 Audio Language Selection 4. 3 Time Zone adjustment 4. 4 Satellite configuration 5. 0 mAIn mEnU 5. 1 Installation 5. 2 Program Setting 5. 3 User preference 5. 4 System Setting 5. 5 Utility 6. 0 oThER oPERATIons 6. 1 Electronic program guide (EPG) 6. 2 Zapping and information banners 6. 3 Audio Language selection 6. 4 Channel list and view mode 6. 5 FAV list 6. 6 Teletext function 6. 7 Subtitle function 6. 8 Sleep Timer function 6. 9 Zoom function A. 1 TRoUblEshooTIng A. 2 PIn CoDE A. 3 sPECIfICATIons 2 2 3 3 3 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 6 8 8 9 9 10 10 10 10 11 11 11 11 11 11 11 12 12 1 English PART 1 · English 1. 0 InTRoDUCTIon 1. 1 safety Instructions Grounding, Polarization -- If this product is used with a specified AC adapter, the adaptermay be equipped with a polarized alternating current line plug (a plug with one blade wider than the other). This safety feature allows the plug to fit into the power outlet only one way. If you cannot insert the plug into the wall outlet, pull it out, reverse it, and then reinsert it. If the plug still fails to fit, contact an electrician and have the receptacle replaced n Protecting the Power Cord -- The power supply cord should be placed so it will not bewalked on. [. . . ] Press oK button to move the dish to exact position of the satellite Use the tu buttons to select YES if you want to search only for Free-To-Air channels and NO if you want to search for scrambled channels as well. Use the tu buttons to select the scan mode for Transponder, Satellite or Advanced Scan. 5. 1. 2 Edit satellite data Dependent on the focus you set with the tu buttons you can edit a satellite or its transponder data. Select a satellite or transponder with the pq buttons and press oK to enter the menu, then PIN-code (default: 0000) is requested. In case you have chosen satellite, the following possibilities are available: Rename, Delete, Move, Add. Rename: Now you can use the tu and pq buttons to choose characters from the shown keyboard, press oK to insert. Press gREEn (Back) button to delete character and use the RED (oK) button to confirm the new name. A message will appear, press oK if you want to delete the satellite or EXIT to cancel. Move: Here you can move the position of the selected satellite in the satellite list. Add: Use the numeric buttons to enter orbital position of the new satellite and tu to select between East or West. In case you have chosen transponder these possibilities are available: Delete, Edit, Add. Edit: Use the numeric buttons to enter the new value for the selected Frequency and Symbol rate and use the tu buttons to select the correct Polarisation and FEC. Use the pq buttons to select the satellite you want to remove, press oK to enter the menu, then PIN-code (default: 0000) is requested. You will be asked for confirmation to delete (oK) or cancel (EXIT). 5. 1. 3 Remove satellite 7 English GOTO X settings: Motor: PART 1 · English 5. 1. 4 satellite search In Satellite Search menu you'll find satellite list and transponder list. Select one or more satellite(s) you want to search and press oK to select. Press RED if you want to Scan ALL channels or gREEn to Scan Free channels. 5. 1. 5 manual TP search This menu allows you to search for specific transponders. Use the pq and tu buttons to select the satellite and transponder you want to search for. Furthermore you can use Network search function to find new appeared transponders. noTE: If Network search function is set to "NO" then receiver will search for the channels that are available from preset transponder table of selected satellite. If it is set to "YES" then receiver additionally search for channels from new transponders via NIT (Network Information Table). Use this option to get newly appeared channels from the satellite. 5. 1. 6 mysat search This function will help you to easily and quickly setup satellite installation. Once receiver has finished you will see satellite/s which is/are found and can execute channel search for Scan ALL channels (RED) or to Scan Free channels (gREEn). 5. 2 Program setting 5. 2. 1 Edit Channels In this menu, you can Rename (YElloW), Move (gREEn), Delete (RED) and Lock (blUE) channels. Use the pq buttons to select a channel which you want to edit and then press the corresponding button. [. . . ] noTE: Audio track with "(AC3)" sign can be listened only if receiver is connected via SPDI/F to digital audio amplifier and it is switched ON. 10 PART 1 · English 6. 4 Channel list and view mode In viewing mode press oK button and the channel list will be shown. Press the pq buttons to select the channel and press the oK button to view selected channel. You can sort channels by FTA -> CAS by pressing the RED button, or A-Z by pressing the YElloW button. You can select satellite by pressing the gREEn button. 6. 5 fAV list In viewing mode, you can get the Favorite channel list by pressing the fAV button. [. . . ]