User manual STRONG TDT PREMIUM BROCHURE

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. Read All Instructions ­ Before you use the product, read all operation instructions, For more information on accessories such as the lithium ion battery, refer to the manuals provided with those products. save These Instructions ­ Save all safety and operating instructions for future reference. heat Warnings ­ Read carefully and follow all warning labels on the product and those described in the instructions. [. . . ] If rechargeable accumulators instead of batteries are going to be used, we recommend using (e. g. NiMH) types with low self-discharge to ensure long time operation of remote control. 4 PART 4 · English 2. 0 ConnECTIon 2. 1 Connecting to Tv and Terrestrial Antenna 2. 2 Connecting to a Digital Audio Amplifier To receive the broadcast signal, the terrestrial antenna cable should be connected to the ANT IN connector at the back of the receiver. 1) Connect your Digital Audio Amplifier with the S/PDIF connector on the back of the receiver (Fig. Tv sCART Connector To connect your receiver with your TV set using a SCART cable. Power Cord Your receiver requires a voltage of 220 ­ 240 V AC (Autoselectable), 50/60 Hz +/-5 %. Make sure to check the power specification before connecting your receiver to the wall outlet. 3. 3 Remote Control 1. Pg+/PgDTv/vCR Info vol+/volmEnu EXIT pq Turns the receiver On/Standby Mutes audio output of the receiver Page up/down No function Shows the actual channel information Volume up/down Opens the main menu/In menu you will get one step back Exits from the menu or sub-menu Menu Off: Change channel to previous/next. Menu On: Change settings for specific Menus Menu On: Activates the highlighted menu item. Menu Off: Displays the current channel list No function No function Fig. ColouRED buTTons for Teletext and other functions 3. 4 Default PIn- code: 0000 4. 0 fIRsT TImE InsTAllATIon 5. 0 mAIn mEnu 5. 1 Channel noTE: If you use the receiver for the first time, the "Easy Install" menu appears. Use qp to select Region, OSD Language, Antenna Power and Scan Mode and tu to select options. Press EXIT button to exit. 5. 2. 4 lCn mode If LCN (Logical Channel Numbering) is activated and LCN signal is provided by the operator, channels will be stored in operator defined order. You can activate/deactivate the LCN function by setting the LCN Mode to ON or OFF. 8 PART 4 · English 5. 3 setup This menu allows you to set OSD Language, Subtitles preference, TV System, Region and Time, Timer Setting, OSD Setting and Parental Lock. Press EXIT button to exit. 5. 3. 1 osD language This menu allows you to set the OSD Language. 5. 3. 2 subtitles preference This menu allows you to set the preferred Subtitles Language and to switch Subtitles Type between Normal and Hard of Hearing. This menu allows to setup different settings concerning your TV set. Display Mode: PAL/NTSC/AUTO Aspect Ratio: Use this menu to configure the screen aspect. Possible settings are: 4:3PS (Pan&Scan), 4:3LB (Letter Box), 16:9 (Wide Screen) and AUTO. Video Output: Use this menu to switch the video output mode between RGB and CVBS. 5. 3. 3 Tv system Here you can set your region and time zone. GMT Usage: This setting allows you to switch the usage of GMT time on or off. The options are: Off / User Define / By Region GMT Offset: This menu is valid only when User Define is selected in GMT Usage menu. The GMT offset range is -11:30 ~ +12:00, increasing by half hours progressively. Date/Time: Date and Time menus are valid only when Off is selected in GMT Usage menu. [. . . ] noTE: You can also press oK to pause playing. 5. 4. 3 load factory Default WARnIng: This option allows you to reset the receiver to factory settings, which clears all stored channels and settings. This option will permanently delete all your settings and channel lists and set your receiver to factory default!Input the correct password using the numeric buttons (the default password is "0000"). During this process nEvER disconnect the receiver from the mains or switch OFF the power! [. . . ]