User manual SYMPHONIC SV206G

[. . . ] CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. [. . . ] ¡If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. Repeat only if there is a power failure or if the VCR is unplugged for more than 30 seconds. (In these cases, the programmed channels are erased. ) ¡You must follow the steps below before attempting to play or record a video tape. If you want to play or record a video tape BEFORE programming the tuner, you can cancel it by pressing CLEAR/C. RESET. 5 Begin channel preset by pressing B once. The tuner scans and memorizes all active channels in your area. ¡The VCR distinguishes between CH 01 AUTO SET UP standard TV channels and cable channels. 6 After scanning, the tuner stops on the lowest memorized channel. ¡If "AUTO SET UP" appears on the TV screen again, check the cable connections. Press B once again and the VCR will begin preset again. TO SELECT A DESIRED CHANNEL You can select the desired channel by using SKIP/CH. (o/p) or by directly pressing the Number buttons on the remote control. Note for using the Number buttons: ¡When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number. (For example: 117, press 1, 1, 7) ¡You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on). TO PRESET THE CHANNELS AGAIN 1 Press MENU until the main menu appears. (If you have already set the clock, you only have to press it once. If not, you have to press it twice). 1 You need to connect the antenna or cable to the VCR first. Then, connect the DVD /VCR power plug to a standard AC outlet. 2 Turn on the TV and set the TV to channel 3. (See "RF OUTPUT CHANNEL" on page 13 for the detail. ) the on-screen menu still remains, press CLEAR/C. RESET to exit the menu. ¡To cancel the Auto repeat mode, press B at step [3] so that OFF appears next to "AUTO REPEAT". SEARCH FUNCTIONS VCR PICTURE SEARCH If you want to skip or repeat a scene during playback, press D or E. ¡Press it again and the VCR will now search at super high speed. (in the LP/SLP modes only). 3 Begin playback by pressing PLAY. ¡Tracking adjustment will be done automatically (Digital Tracking function) when you start playback. ¡When a tape has reached the end, the VCR will rewind the tape to the beginning, and eject the tape. INDEX SEARCH An index mark will be assigned at the beginning of each recording you made. You may skip to a specific marked point by following the steps below. 4 To stop playback, press STOP. ¡If no corresponding symbols appear on the display when you press buttons such as PLAY, RECORD, D or E, that means no cassette tape is in the VCR. Please insert a tape. 1 Press SEARCH MODE so that the Index Search menu appears. Counter Reset ¡You can reset the counter by pressing 2 Enter the number of recordings you wish to skip by pressing K or L within 30 seconds. INDEX SEARCH 03 CLEAR/C. RESET on the remote control twice. STILL/SLOW You can freeze the picture on TV screen by pressing PAUSE during playback. ¡You can advance the picture one frame at a time by pressing PAUSE during the Still mode. However, if the picture begins to vibrate vertically during the still mode, you can stabilize the picture by pressing SKIP/CH. ¡If the picture is distorted or rolling vertically, adjust the vertical hold control on your TV, if so equipped. [. . . ] ¡Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analogue records. while the TV program reception is clear. Dirt accumulated on the video heads after long periods of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in your DVD/VCR COMBINATION UNIT may need to be cleaned. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner. [. . . ]