User manual TANNOY MERCURY FR

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual TANNOY MERCURY FR. We hope that this TANNOY MERCURY FR user guide will be useful to you.


TANNOY MERCURY FR : Download the complete user guide (688 Ko)

Manual abstract: user guide TANNOY MERCURY FR

Detailed instructions for use are in the User's Guide.

[. . . ] The HTI88 subwoofer is not video-shielded and should not be placed near a video display. Installing the HTI88 near a corner will tend to maximize lowfrequency output. Be cautious when installing in a corner, to avoid a "boomy" sound. Also take into consideration any unusual features of the room, such as an alcove, which may tend to create a localized node that may affect bass response in that area of the room. [. . . ] Also take into consideration any unusual features of the room, such as an alcove, which may tend to create a localized node that may affect bass response in that area of the room. It is generally recommended that the speaker be installed so that the bottom of the speaker is approximately 12" from the floor. Note that installing the speaker within the MERCURY FR back box as shown in the illustration to the left will achieve the recommended height. Since every listening room is different, TANNOY strongly recommends experimenting with the positioning of your subwoofer prior to cutting the wall to obtain the most pleasing results in your room. One technique that can help you find the ideal subwoofer location is to temporarily borrow a standalone subwoofer and place it near the main listening location. Then move around the room and determine where you hear the most pleasing bass performance. This would then be the ideal location for the subwoofer. 14. 00 CABINET INCLUDED MERCURY FR One MERCURY FR back box (shown installed between 16" on-center wall studs) (4) L-brackets (8) #10 32 x 1" screws (L-brackets to back box) (8) #10 split washers (L-brackets to back box) (8) #10 flat washers (L-brackets to back box) (8) #8 x 3/4" wood screws (L-brackets to wall studs) (2) wood centering bars (4) #10 32 x 1-1/2" flat-head screws (centering bars to back box) NOTE: The back box is shipped with the two centering bars attached to it using the four flat-head screws. 68. 00 CABINET DAMPING PADS LOCATING BARS ® HOME THEATER IN-WALL SERIES 4. 00 MERCURY FR OWNER'S GUIDE 2. 49 SPEAKER CONNECTIONS Connection Tips Refer to page 4 of the HTI88 subwoofer owner's guide for general information on speaker-wire connections. This manual includes connection guidelines that are specific to the MERCURY FR back box. To use the push-type terminals on the connections panel supplied with the MERCURY FR back box enclosure, depress the colored cap until the pass-through hole in the binding post is revealed. While holding the cap down, insert the bare end of the wire, or a banana plug, into the pass-through hole. When used, the MERCURY FR back box is installed during new construction before the wallboard. Using the four flat-head screws, install the two centering bars as shown in Detail B in the drawings. They also help locate the left/right position of the enclosure as they can be mounted into the studs on the left and right to hold the enclosure in the correct location before final mounting. Using the eight #10 32 x 1" screws, install the four L-brackets at the four corners of the enclosure. Each of the eight screws should have both the split washer and flat washer installed; the split washer goes on first. Leave the screws a half-turn loose at first to allow for adjustment later (see Detail A). Do not screw the L-brackets to the wall studs at this time (see step 6). The bottom edge of the bottom L-brackets will rest against the baseboard 2 x 4. At this time, make note of adjustments necessary to square the enclosure into the wall (see Detail C). After refitting and tightening the L-brackets into the enclosure (but not the wall studs yet), fit the enclosure into the wall once again. See Detail A Detail C L-Brackets See Detail B 6. [. . . ] At this time, make note of adjustments necessary to square the enclosure into the wall (see Detail C). After refitting and tightening the L-brackets into the enclosure (but not the wall studs yet), fit the enclosure into the wall once again. See Detail A Detail C L-Brackets See Detail B 6. Remove the wood centering bars and replace the flat-head screws into the holes left over (the holes left in the cabinet face underneath the bars are also counterbored to accept the flat-head screws). The enclosure is now installed and ready for the wallboard to be installed over it. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE TANNOY MERCURY FR




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual TANNOY MERCURY FR will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.