User manual TEKA LP2 800

[. . . ] (A) re 1 pW). Pega para a Extracção das Bandejas A pega para e extracção das bandejas utiliza-se quando é necessário deslocar a bandeja para verificar o estado do cozinhado. Para manusear a bandeja fora do forno é necessário utilizar luvas protectoras. Gancho curto Gancho longo HI-735/HI-735 ME 1 Control Panel with anti finger-mark varnish 2 Oven Seal 3 Fold-down Grill element 4 Catalytic Side Panel(**) 5 Grid 6 Telescopic Guides(**) 7 Cake Tray(*) 8 Roasting Tray(*) 9 Door switch 10 Hinge 11 Door 12 Air Outlet 13 Fixing to Unit 14 Grill Screen 15 Smoke Outlet 16 Light 17 Catalytic Rear Panel 18 Tray Handle 19 Fan 20 Large Interior Glass Door 1 12 13 14 15 16 17 18 19 2 3 4 5 6 7 8 9 10 11 20 Posição para a bandeja de pastelaria. O gancho curto coloca-se por cima da bandeja. Posição para a bandeja profunda. [. . . ] O gancho longo coloca-se por cima da bandeja. (*) Informação Técnica O forno atinge uma temperatura na porta inferior a 60 K (conforme EN 60335-1/2-6). (**) Inside oven and trays with easy cleaning enamel. Depending on the model. Control Panel Model HI-735 1 23 45 HI 735 mode Model HI-735 ME 1 6 23 45 HI 735 ME 7 7 7 7 mode 1 Electronic timer. Indicates that heat is being passed to the food and it goes out when the set temperature is reached. 7 Control knobs for the hob. 13 ENGLISH Oven Functions Setting the time on the clock Switch off oven Caution While using the Grill, MaxiGrill or MaxiGrill with fan, the door must be kept closed. Use of the Oven Programming the cooking time 1 Press the MODE button until the indicator above the symbol begins to flash. 2 Select the length of time, pressing the "+" or "-" buttons. 3 Subsequently, the indicator that was flashing will light, indicating that the oven will switch itself off automatically. 6 When the set time has elapsed, the oven will disconnect, an alarm will sound and the indicator will begin to flash. 8 Set the controls in the position to switch off the oven. Conventional It is used for sponges and cakes where the heat received must be uniform to achieve a spongy texture. Conventional with fan Appropriate for roasts and cakes. The fan spreads the heat uniformly inside the oven. Turbo The fan distributes the heat produced by an element located at the rear of the oven. Due to the uniform heat distribution, it allows roasting and baking to take place at two heights at the same time. To do this, set the temperature selector to position. On connecting the oven, you will notice that 12:00 appears on the clock and that a light begins to flash above the symbol. It is recommended to put the item on a rack with a tray beneath to collect the stock and juices. Grill and Lower element Special for roasts. Note The pilot light remains on in any cooking function. This function may be used even though you are already cooking in your oven. To do so, follow the instructions given except Nº 5. 14 15 ENGLISH Programming the end of cooking time for the oven Tray Handle Programming the duration and automatic stop 1 Press the MODE button until the indicator above the symbol begins to flash. 2 Select the length of cooking time pressing the "+" or "-" buttons. 4 Press the mode button until the indicator above the symbol begins to flash. 5 Select the time that cooking should finish pressing the "+" or "-" buttons. 8 The oven will remain disconnected with the indicators above the and symbols lit. 9 When the time to begin cooking is reached, the oven will switch itself on and will continue cooking during the programmed time. 10 When the programmed finishing time is reached, the oven will disconnect, an alarm will sound and the light above the symbol will begin to flash. 11 Press any button to switch off the alarm and the oven will reconnect. to mode Caution Pressing the MODE button the display on the screen shows any function p rogrammed. [. . . ] to mode Caution Pressing the MODE button the display on the screen shows any function p rogrammed. It can be changed by pressing the "+" or "-" buttons. On selecting the desired function, the indicator above the corresponding signal will light. In the event of a power cut, all the programming of the electronic clock will be erased. [. . . ]