User manual TEKTRONIX TLA5000B DATASHEET

[. . . ] Timing Record Length (quarter/half/full channels with time stamps and with or without transitional storage) ­ 8/4/2 Mb, 32/16/8 Mb, 128/64/32 Mb per channel. Timing Record Length with Glitch Storage Enabled ­ Half of default main record length. Channel-to-channel Skew ­ 1 ns (900 ps typical). Minimum Recognizable Pulse/Glitch Width (single channel) ­ 1 ns (P6410, P6419, P6450) 1. 25 ns (P6434). Minimum Detectable Setup/Hold Violation ­ 250 ps. [. . . ] Setup-and-Hold Violation Recognizer Setup Time Range ­ From 8 ns before to 7. 5 ns after clock edge in 125 ps increments. Setup-and-Hold Violation Recognizer Hold Time Range ­ From 7. 5 ns before to 8 ns after clock edge in 125 ps increments. MagniVuTM Trigger Position ­ MagniVu position can be set from 0% to 60% centered around the MagniVu trigger. Storage Control (data qualification) ­ Global (conditional), by state (start/stop), block, by trigger action, or transitional. Force main prefill selection available. 2 www. tektronix. com Logic Analyzers -- TLA5000B Series iViewTM (Integrated View) Capability Number of Oscilloscopes that can be Connected to a TLA System ­ 1. External Oscilloscopes Supported ­ For a complete list of currently External Peripheral Interfaces External Display Port Type ­ Two female DB15 SVGA. External Display Resolution ­ Up to 1600×1200 noninterlaced at 16. 8 M colors. Parallel Interface Modes ­ Centronics mode, EPP (Extended Parallel Port), ECP supported oscilloscopes that are supported, please visit our website http://www. tektronix. com/iview. Oscilloscope Connections ­ GPIB, Trigger In, Trigger Out, Clock In (when available) for the GPIB iView cable (Opt 1C). Data Correlation ­ After oscilloscope acquisition is complete, data is automatically transferred to the TLA and time correlated with the TLA acquisition data. Deskew ­ Oscilloscope and TLA data is automatically deskewed and time correlated when using the iView external oscilloscope cable. iView External Oscilloscope Cable Length ­ 2 m. (Microsoft high-speed mode). Serial Interface Port Type ­ Male DB9. USB Port ­ Four USB 2. 0. PC Characteristics Operating System ­ Microsoft Windows XP Professional with Multilingual User Interface Pack. Optical Drive ­ Internal 24/10/24 CD-RW. Symbolic Support Number of Symbols/Ranges ­ Unlimited (limited only by amount of virtual memory available on TLA). Object File Formats Supported ­ IEEE695, OMF 51, OMF 86, OMF 166, OMF 286, OMF 386, COFF, Elf/Dwarf 1 and 2, Elf/Stabs, TSF (TSF is a generic ASCII file format documented in the TLA user manual). If a format is not listed, please contact your local Tektronix representative. Integral Controls Front-panel Display ­ External Instrumentation Interfaces System Trigger Output ­ Asserted whenever a system trigger occurs (TTL-compatible output, back-terminated into 50 ). System Trigger Input ­ Forces a system trigger (triggers all modules) when asserted (TTL-compatible, edge-sensitive, falling-edge latched). External Signal Output ­ Can be used to drive external circuitry from a module's trigger mechanism (TTL-compatible output, back-terminated into 50 ). External Signal Input ­ Can be used to provide an external signal to arm or trigger Size: 10. 4 in. [. . . ] Safety ­ UL3111-1, CSA1010. 1, EN61010-1, IEC61010-1. Ordering Information TLA5201B TLA5202B TLA5203B TLA5204B 34 Channel, 2 GHz Timing with 125 ps MagniVuTM Acquisition, 235 MHz State, 2 Mb Logic Analyzer. 68 Channel, 2 GHz Timing with 125 ps MagniVuTM Acquisition, 235 MHz State, 2 Mb Logic Analyzer. 102 Channel, 2 GHz Timing with 125 ps MagniVuTM Acquisition, 235 MHz State, 2 Mb Logic Analyzer. [. . . ]