User manual THUNDER TIGER MTA4 S28

[. . . ] Extension cords do not guarantee the required safety of the appliance (e. g. To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system. If there is any doubt, have the electrical system of the house checked by a qualified electrician. damaged it must only be replaced by a Miele Service technician with a genuine Miele power cord. [. . . ] The program starts and "Items can be added" appears in the display. As long as this reference is shown, tableware can be added to the machine without impairing the cleaning result. Time display Before the program starts, the time display shows the running time of the selected program in hours and minutes. During the running program the remaining time is shown in the time display. The running time for the same program may vary depending on the intake water temperature, load size and soiling. When a program is selected for the first time, a time is shown which equals an average program running time with cold water. Each time a program is run, the electronic adjusts the program running time according to the intake water temperature and the load size. , The water in the dishwasher is hot, risk of burns by splashing water. Cancel a program only in the first few minutes. the water softening) could be interrupted. 40 Use Standby A few minutes after the last key is pressed or at the end of the program the dishwasher switch into Standby mode to save energy. This feature can also be turned off (see "Settings - Optimize standby"). If refill salt and/or rinse aid or a fault are present in the display, the dishwasher will not turn off. At the end of a program At the end of a program the optical control light flashes slowly with the door closed. The optical function light goes out one hour after the end of a program. At the end of a program the display shows Program finished or Drying plus with the door slightly open (if activated). With the door open the light turns off automatically after 15 minutes The light can also be turned off. The door must be opened enough so that the interior lighting turns on then off. ^ To turn the light on again, repeat the above process. 46 Settings ! The "Settings J" menu allows you to adjust standard settings Opening the Settings J menu ^ Turn the dishwasher on K. If the memory function is selected, the last selected program is displayed. Switch to the main menu by pressing "Clear" U. } Settings F } Sensor Wash Main menu r ^ Select "Settings J". The display changes into the menu "Settings J". } Language F } Time of day Language r ^ Select the menu option you would like to change. Press the : button to see more information about the option currently selected. The selected options in the submenus are marked with a check L. 47 Settings ! Language J The display contents can be shown in different languages. The displayed language can be changed by the submenu "Language J". The flag behind the word Language J serves as a guide when an unfamiliar language is selected. Select the respective menu with a flag until the submenu Language J appears. Time of day This selection allows the clock to be shown as 24 or 12 hours. After confirming the minutes with OK, the display will revert to the previous menu. [. . . ] Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified electrician. If there is any question concerning the proper electrical connection or grounding of this appliance to the power supply, please consult a licensed electrician or call Miele's Technical Service Department: U 1-800-999-1360 V 1-800-565-6435 Specifications The dishwasher comes equipped with a 4 ft (1. 2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle. 79 Electrical connection Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable. , Prior to making a hardwire , CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer cannot be held responsible. Before connecting the appliance to the power supply, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. [. . . ]