User manual TOSHIBA TDP-FF1
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual TOSHIBA TDP-FF1. We hope that this TOSHIBA TDP-FF1 user guide will be useful to you.
Manual abstract: user guide TOSHIBA TDP-FF1
Detailed instructions for use are in the User's Guide.
[. . . ] OWNER'S MANUAL
LED PROJECTOR TDP-FF1A
Before Using
Operations
Others
Preparations
SAFETY PRECAUTIONS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: Handling the cord on this product or cords associated with accessories sold USA only with this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. [. . . ] Normal mode: · When OSD is not displayed: Volume control (Computer, Video input) · When OSD is displayed: Choose menu item File view mode: · When OSD is not displayed: Choose file or directory · When OSD is displayed: Choose menu item Slideshow mode: · Show previous/next slide Normal mode: · When OSD is not displayed: AUTOSET (RGB signal) · When OSD is displayed: Confirm screen menu selections File view mode: · When OSD is not displayed: Highlight on a file: Start the slideshow Highlight on a directory: Change the directory · When OSD is displayed: Confirm screen menu selections Slideshow mode: · To pause or re-start the slide show
2.
<, > +
3. AUTOSET /
18
Remote control keypad and functions
Remote Control
8 7 6 5
1 2 3 4
1. AUTOSET 2.
Auto set Normal mode: · When OSD is not displayed: No action · When OSD is displayed: Confirm screen menu selections File view mode: · When OSD is not displayed: Highlight on a file: Start the slideshow Highlight on a directory: Change the directory · When OSD is displayed: Confirm screen menu selections Slideshow mode: · To pause or re-start the slide show Adjust volume Correct image distortion Pause image (Computer, Video input only) Display menu system/move to upper level in menu system Normal mode: · When OSD is not displayed: No action · When OSD is displayed: Choose menu item File view mode: · When OSD is not displayed: Choose file or directory · When OSD is displayed: Select screen menu items Slideshow mode: · Show previous/next slide Select input sources
3. Input
19
Preparations
Using the battery pack with the projector
The following procedures are for the installation of the battery pack with the projector.
Installing the battery
Turn off the power switch and disconnect the AC adaptor. Plug in the battery pack.
Press down the battery pack firmly until it clicks into place. Switch the power button to turn on the projector.
Remove the battery
Turn off the power switch and disconnect the AC adaptor. Close the battery connector cover.
2
1
3
Charge the battery
The battery pack can be charged with the projector when the AC adaptor is connected. It takes 3 to 4 hours to charge the battery completely.
20
Notes
· Remove the battery if the projector is not in use, otherwise the battery will gradually discharge. · When the battery capacity become less then 10%, the following message appears: The battery capacity is less than 10%.
· Press any key to make the warning message disappear. · When the projector runs out of the battery, it shuts down automatically after showing the message "The projector is shutting down". · The projector will work for approximate 2 hours with full charged battery at room temperature (25°C). · The battery is consumables, it can be recharged approximately 500 times. · It is recommended that you replace to a new battery when the operation time with the battery becomes significantly short. (contact reseller for details) · Do not touch the battery connector. Before taking it to the center, stick insulating tape to the terminal.
Specifications for TOSHIBA Li-ion battery
· Model name: TLPBP1 · Output voltage: 7. 4V · Capacity: 4400mAh · Operating temperature: 5°~35°C (41°~95°F) · Dimensions: 138(W)x56(H)x26(D) mm · Weight: 0. 25kg
· Always observe the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when handling the battery.
Warning
21
Preparations
Using the remote control
Changing the new lithium battery
Remove the battery compartment. Replace the lithium battery.
Insert the battery compartment.
Be sure to align the battery according to the polarity.
Operating the remote control
Note
Turn on the projector and then the remote control can be used to adjust the OSD, volume, and input select.
· The remote control is shipped with a plastic sheet between the battery and its contact. · Remove the battery from the remote control when it will not be used for an extended period.
Battery
· Before using the battery, please refer to the notes on . · If the remote control stops working, or if its range decreases, replace the battery with new one. · The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting. · In rare cases, ambient conditions could impede the operation of the remote control. If this happens, point the remote control at the main unit again, and repeat the operation.
The remote control
22
Placement
Placement Styles
The factory setting is "floor-mounted front projection. " Set the [Projection mode] in the Default setting menu , in accordance with your needs.
· Always observe the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
Warning
Projection Distance and Size
Screen
Top view
a (min length) =
projection size (inches) 27. 3403
FF1 uses a fixed lens.
projection size (inches) 11 17 25 30 35 40 45 50 60 68 projection distance (m) 0. 40 0. 62 0. 91 1. 10 1. 28 1. 46 1. 65 1. 83 2. 19 2. 49 height (H) (cm) 1. 7 2. 6 3. 8 4. 6 5. 3 6. 1 6. 9 7. 6 9. 1 10. 4
Side view
Lens center
Note: 110% offset condition
a is the distance (m) between the lens and the screen, and corresponds to a range of 0. 4 m to 2. 5 m. H is the height from the image bottom to the center of the lens.
23
Preparations
Use the figures, tables, and formulas below to determine the projection size and projection distance. [. . . ] Description Input source name Resolution (in dots) Display color method of video signal Display the battery remains Firmware version [Note] RGB Yes Yes No Yes Yes Y/PB/PR Yes No Yes Yes Yes
"Yes": displayed, "No": not displayed
Video Yes No Yes Yes Yes
USB Yes No No Yes Yes
39
Operations
2. [Firmware version] shows the version of the projector's internal control program. This version is referred to for customer service, etc.
Lens and main unit cleaning
Lens cleaning
· Clean the lens with a commercially available blower and/or lens cleaner. · The lens is easily scratched, so do not rub it with hard objects, or strike it.
Main unit cleaning
· Clean the main unit after unplugging the power cord. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TOSHIBA TDP-FF1
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual TOSHIBA TDP-FF1 will begin.