User manual TP-LINK SL2226P+

[. . . ] COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK Technologies Co. , Ltd. All rights reserved. COPYRIGHT & TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the color of the device icon is green, click the right button on the icon, then pop up a menu, click connect, you will see the interface as figure 5-10. Figure 5-10 - 13 - TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide The color of the port on the panel is yellow, which means that the port is in connection. If the color of the port frame is red, it's said that the port is management port. 5. 2. 3 Configuration If the device is well connected, you can configure the switch now. Disconnect When the device is in connection, if at the moment it does not need management, you can choose the Close Group button to close the group. Reset When the device is in connection, if resetting needed, click main menu ->Device->Reset, a dialog will pop up. Resume Factory Setting When the device is in connection, if resuming factory setting needed, click main menu ->Device->Resume Factory Setting, a dialog will come out, click ok on the dialog, then the switch will resume factory setting. Change Password When the device is in connection, if you want to change password, click main menu->Device->Change Password, a dialog will be pop up, you can change password in the dialog, the length of password is not more than 7. VLAN Config The TL-SF2226P+ can support three VLAN modes, no VLAN, port VLAN and tag VLAN. Default Setting: no VLAN. Steps of Setting: If VLAN mode is no VLAN, or you want to change current VLAN mode, you should select one mode you want to. As figure 5-11. - 14 - TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide Figure 5-11 Current VLAN mode is shown in the combo box, select one mode you want in the combo box and click OK. If you change the VLAN mode, the information of previous VLAN will be lost and the switch will give new default information about VLAN. If the VLAN mode is tag VLAN, all ports will be in a VLAN which tag's value is 1. Click main menu->Config->VLAN Config, under the view, you will see the VLAN list box. If the VLAN mode is port VLAN, select or delete some ports you want to change in the pop-up dialog. As figure 5 -12. Figure 5-12 If the VLAN mode is tag VLAN, Configure tag VLAN in the pop-up dialog. For more details, please read the help file. - 15 - TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide Figure 5-13 Now go back to the main menu->Config->VLAN Config->Config Effect, Only execute this step, the Configuration will be valid. The switch looks a TRUNK as a big port regardless of it's composition. Default setting: no TRUNK. Steps of setting: Click main menu->Config-> TRUNK Config->Config Effect or click the TRUNK icon on toolbar. As figure 5-14. Figure 5-14 Double click the TRUNK you want to config in the TURNK list box, TRUNK configuration dialog will pop up, and you can config the TRUNK now. For more details, please refer to - 16 - TL-SF2226P+/TL-SL2226P+ help file. Remote Smart Switch User Guide Now go back to main menu->Config->TRUNK Config->Config Effect. Figure 5-15 Only execute this step, the Configuration will be valid. Port Config Click main menu->Config->Port Config or double click a port in the port list box. As figure 5-16. Figure 5-16 Now you can configure each parameter of the port except port priority. auto-test the speed and negotiate the duplex mode with the - 17 - TL-SF2226P+/TL-SL2226P+ 10HD: 10Mbps, Half-Duplex. [. . . ] If the VLAN Mode is 802. 1Q VLAN, the ports must have the same tag - 28 - TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide rule when they are in the same VLAN. When you enable or disable a TRUNK, the switch will lose the info of static binding address which is relate to the TRUNK or the 4 ports. MAC Table Aging Time MAC Table Aging Time interface is as follows: Figure 6-12 Priority Management Priority Management interface is as follows, when the sate is close, other parameters can't be changed. Figure 6-13 Static MAC Table Static MAC Table interface is as follows: - 29 - TL-SF2226P+/TL-SL2226P+ Remote Smart Switch User Guide Figure 6-14 Press Enter, you will see the interface as follows. Figure 6-15 There are three operations in Static MAC Table, add, delete and edit. Caution: If you configure the Static MAC Table, it will take effect immediately, you needn't save it. [. . . ]