User manual TP-LINK TL-PA4010KIT

[. . . ] No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO. , LTD. All rights reserved. http://www. tp-link. com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. [. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. CONTENTS Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Chapter 1. Connecting the PoE Supplier Adapter You can use TL-PA4010KIT PoE Supplier Adapter with PD or PoE Receiver Adapter to expand your network to where there are no power lines or outlets, where you wish to fix devices such as APs, IP Cameras or IP Phones, etc. The following steps will tell you how to connect the PoE Supplier Adapter correctly. Use a CAT5 UTP cable to connect port of Ethernet device (such as a switch, hub or router) to the LAN IN port. Please connect the power adapter properly to a power socket with provided power cable, and then connect the other end of the power adapter to the DC 48V port of the TL-PA4010KIT. 3 3. Connect the POWER+DATA OUT port of the TL-PA4010KIT to a PD or a PoE Receiver Adapter with CAT 5 UTP cable. Now, the device can work normally with data and power. If the device supports PoE (take an IP camera with PoE for example), following topology will work: Switch TL-SF1008D Power Adapter CAT5 UTP Cable (Data) Power Cable (Power) TL-PA4010KIT IP camera with PoE CAT5 UTP Cable (Power & Data) ` 2. PC If the device does not support PoE, it is necessary to have a PoE Receiver Adapter to separate the power and data, transmitting them detached in one UTP cable and one power cable. [. . . ] If the device supports PoE (take an IP camera with PoE for example), following topology will work: Switch TL-SF1008D Power Adapter CAT5 UTP Cable (Data) Power Cable (Power) TL-PA4010KIT IP camera with PoE CAT5 UTP Cable (Power & Data) ` 2. PC If the device does not support PoE, it is necessary to have a PoE Receiver Adapter to separate the power and data, transmitting them detached in one UTP cable and one power cable. You can use following topology: 4 Power Adapter Notebook With Wireless Adapter Power Cable (Power) TL-PA4010KIT CAT5 UTP Cable (Data) CAT5 UTP Cable (Power & Data) TL-POE10R Power Cable Switch TL-SF1008D CAT5 UTP Cable (Data) Wireless AP TL-WA601G Note: Do not mistake the power port of the TL-PA4010KIT and TL-POE10R when choosing the scheme 2, or else it will cause serious damage to your network device. [. . . ]