User manual TP-LINK TL-R4299G

[. . . ] TL-R4299G Dual-WAN SMB Broadband Router Rev: 1. 0. 3 1910010055 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO. , LTD. Other brands and product names are trademarks or http://www. tp-link. com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] It can be a service port or a range of service ports (the format is XXX - YYY, XXX is Start port, YYY is End port). IP Address - This field displays the IP address of the PC running the service application. Protocol - This field displays the protocol used for this application, either TCP, UDP, or All (all protocols supported by the router). Enabled means that the entry will take effect, Disabled means that the entry will not take effect. To add/modify a virtual server entry: Step 1: Click Add New. . . /Modify shown in Figure 4-20, you will see a new screen shown in Figure 4-24. Step 2: Select the service you want from the "Common Service Port", then the port and protocol value will be added to the corresponding field automatically, you only need to configure the IP address for the virtual server; If the "Common Service Port" does not contain the service that you want, please configure the Service Port, IP Address and Protocol manually. 35 TL-R4299G Dual-WAN SMB Broadband Router User Guide Figure 4-24 Step 3: After that, select Enable to make the entry take effect. Note: 6) 7) If you want to add more than one reserved IP, please go to step 1 to continue. It is possible that you configure more than one type of available service on a computer or server, it means the IP addresses for the virtual servers are same. Other configurations for the entries as shown in Figure 4-24: Click the Delete button to delete the entry. Click the Previous button to view the information in the previous screen, click the Next button to view the information in the next screen. Note: If you set the virtual server of the service port as 80, you must set the web management port on System Tools ­> Remote Management screen to be any value except 80 such as 8080. Or else there will be a conflict to disable the virtual server. 4. 5. 2 Port Triggering Choose menu "ForwardingPort Triggering", you can view and add port triggerings in the next screen (shown in Figure 4-25). Some applications require multiple connections, like Internet games, video conferencing, Internet calling and so on. Port Triggering is used for some of these applications that can work with an NAT router. 36 TL-R4299G Dual-WAN SMB Broadband Router User Guide Figure 4-25 Trigger Port - This displays the port for outgoing traffic. An outgoing connection using this port will "Trigger" this rule. Trigger Protocol - This displays the protocol used for Trigger Ports, either TCP, UDP, or All (all protocols supported by the router). Incoming Ports - This displays the port or port range used by the remote system, they are used for responding to the outgoing request. A response using one of these ports will be forwarded to the PC that triggered this rule. Incoming Protocol - This displays the protocol used for Incoming Ports Range, either TCP or UDP, or ALL (all protocols supported by the router). Enabled means that the rule will take effect, Disabled means that the rule will not take effect. Once configured, the operation for Port Triggering will proceed as follows: Step 1: A local host makes an outgoing connection using a destination port number defined in the Trigger Port field. Step 2: The router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host. [. . . ] Type an appropriate number for "Max Idle Time" or "Period of Time" to avoid wasting paid time. Otherwise, you can select "Connect Automatically" for Internet connection mode. Figure B-2 Note: 1) 2) Sometimes the connection can not be disconnected although you specify a time to Max Idle Time, because some applications still visit the Internet continually in the background. If you are a Cable user, please configure the router following the above steps. 76 TL-R4299G 2. Dual-WAN SMB Broadband Router User Guide How do I configure the router to access Internet by Ethernet users? Step 1: Login to the router, click the menu NetworkWAN on the left of your browser, On the WAN screen, select "Dynamic IP" for "WAN Connection Type", and finish it by clicking Save. Step 2: Some ISPs require that you register the MAC address of your adapter, which is connected to your cable or DSL modem during installation. [. . . ]