User manual TP-LINK TL-SG1005D

[. . . ] Do not place heavy objects on the Switch. Chapter 1: Introduction 1. 1 Overview of the product TL-SG1005D TL-SG1008D 5/8-Port Gigabit Ethernet Switch The TL-SG1005D/TL-SG1008D 5/8-port Gigabit Ethernet Switch provides you with a high-performance, low-cost, easy-to-use, seamless and standard upgrade to boost your old network to 1000Mbps. Increase the speed of your network server and backbone connections, or make Gigabit to the desktop a reality. Power users in the home, office, workgroup, or creative production environment can now move large, bandwidth-intensive files faster. [. . . ] The sketches of the front panel, rear panel and LED indicators are very similar to the TL-SG1005D and TL-SG1008D models. The following sketches are for TLSG1008D. 3. 1 Front Panel The front panel of the Switch consists of several LED indicators. Link/Act Power 1000Mbps 10/100Mbps TL-SG1008D 8-Port Gigabit Ethernet Switch 1 2 3 4 5 6 7 8 1. 2 Ø Ø Ø Features Fully Complies with IEEE802. 3, 802. 3u and 802. 3ab standards 5/8 10/100/1000Mbps Auto-Negotiation RJ45 ports supporting AutoMDI/MDIX Supports IEEE802. 3x flow control for Full Duplex mode and backpressure for Half Duplex mode Figure 3-1 TL-SG1008D Switch Front Panel sketch 3. 2 Rear Panel The rear panel of the Switch consists of 8 10/100/1000Mbps RJ45 Ports and one power jack. All ports can work as the Uplink port. 1 8 7 6 5 4 3 2 1 POWER Figure 3-2 TL-SG1008D Switch Rear Panel sketch 3. 3 LED indicators Dimensions(W D H) Power Supply Output: Operating Temperature Storage Temperature Operating Humidity Storage humidity Environmental and Physical 7. 3 5. 7 1. 7 in. (186mm 146mm AC 9V~ 1. 2A 0OC~40OC (32OF~104OF) -40OC~70OC (-40OF~158OF) 10%~90% non-condensing 5%~95% non-condensing FCC STATEMENT 44mm) This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Ø Reorient or relocate the receiving antenna. Ø Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Ø Consult the dealer or an experienced radio/TV technician for help. The LED indicators include Power LED and Link/Act LEDs (See Figure 3-1). The LED indicators are used for monitoring and troubleshooting of the Switch. The following section shows the LED indicators for the Switch along with an explanation of each indicator. Ø Power LED: This indicator will light up when the Switch powers up. One LED will light green when a 1000Mbps device is connected to the corresponding port. [. . . ] E-mail: support@tp-link. com Website: http://www. tp-link. com SAFETY NOTICES Caution: Do not use this product near water, for example, in a wet basement or near a swimming pool. There may be a remote risk of electric shock from lightning. COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Other brands and product names are trademarks or registered trademarks of their respective holders. [. . . ]