User manual TP-LINK TL-SL3428 EMBEDDED WEB SYSTEM USER GUIDE

[. . . ] Embedded Web System User Guide TL-SG3109 9-port Gigabit Managed Switch TL-SL3428 24+4G Gigabit Managed Switch TL-SL3452 48+4G Gigabit Managed Switch Rev: 1. 0 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK Technologies Co. , Ltd. All rights reserved. FCC STATEMENT This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC Rules. [. . . ] This section contains the following topics: Adding VLAN Defining VLAN Properties Defining VLAN Membership Defining VLAN Interface Settings Configuring GARP Defining GVRP 7. 3. 1 Defining VLAN Properties The VLAN Member Properties Page provides information and global parameters for configuring and working with VLANs. The VLAN Member Properties Page opens: Figure 71: VLAN Member Properties Page The VLAN Member Properties Page contains the following fields: Select VLAN ID -- Displays the properties of the selected VLAN in the VLANs table below. Show All -- Displays the properties of all defined VLANS in the VLANs table below. The possible field values are: ­ Dynamic -- Indicates the VLAN was dynamically created through GARP. Unauthenticaed VLAN -- Indicates whether unauthorized users can access a Guest VLAN. The possible field values are: ­ Enabled -- Enables unauthorized users to use the Guest VLAN. ­ Disabled -- Disables unauthorized users from using the Guest VLAN. The possible field values are: ­ Checked -- Removes the selected VLAN. In the VLAN Member Properties Page, Click The VLAN information is saved and the device is updated. 7. 3. 2 Defining VLAN Membership The VLAN Member Membership Page contains a table that maps VLAN parameters to ports. Ports are assigned VLAN membership by toggling through the Port Control settings. 0 To define VLAN membership: 1. Click System > Bridging Config > VLAN >Membership > Membership. The VLAN Member Membership Page opens: Figure 74: VLAN Member Membership Page The VLAN Member Membership Page contains the following fields: VLAN ID -- Displays the user-defined VLAN ID. VLAN Name -- Displays the name of the VLAN VLAN Type -- Indicates the VLAN type. The possible field values are: ­ Dynamic -- Indicates the VLAN was dynamically created through GARP. R -- Denies the interface VLAN membership, even if GARP indicates the port is to be added. 7. 3. 3 Defining VLAN Interface Settings The VLAN Interface Settings Page contains fields for managing ports that are part of a VLAN. The Port Default VLAN ID (PVID) is configured on the VLAN Interface Settings Page. All untagged packets arriving at the device are tagged with the port PVID. Click System > Bridging Config > VLAN > Membership > Interface Settings. Figure 75: VLAN Interface Settings Page The VLAN Interface Settings Page contains the following fields: Interface -- Displays the port number included in the VLAN. The possible values are: ­ General -- Indicates the port belongs to VLANs, and each VLAN is user-defined as tagged or untagged (full IEEE802. 1q mode). When a port is in Access mode, the packet types which are accepted on the port cannot be designated. Ingress filtering cannot be enabled or disabled on an access port. [. . . ] Detects and uses network topologies that allow a faster convergence of the spanning tree, without creating forwarding loops. Contains all Startup file commands, as well as all commands entered during the current session. After the device is powered down or rebooted, all commands stored in the Running Configuration file are lost. Enables Internet applications to obtain differing service resources for traffic flows. [. . . ]