User manual TYAN THUNDER I7500

[. . . ] Thunder i7500 /// Revision 2. 01 S2720 Copyright © TYAN Computer Corporation, 2001-2002. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Thunder i7500 S2720 are trademarks of TYAN Computer Corporation. [. . . ] The System Time will always display the current time in a 24-hour format. Adjusting the clock in your operating system will also change the System Time inside BIOS setup. System Date displays the current date and can be changed just like System Time. System Time System Date Master/Slave Setup All the options in this section are automatically detected by the motherboard chipset and BIOS. 3. 2 ­ Advanced Settings IDE Configuration Floppy Configuration Boot Settings Configuration SuperIO Configuration Remote Access Configuration Onboard Device Configuration USB Configuration All settings discussed in following sections. 3. 3 ­ IDE Configuration Options related to the IDE controller can be altered through the following. Onboard PCI IDE Controller Primary Master/Slave Secondary Master/Slave Hard Disk Write Protect ATAPI Detect Time Out ATAPI 80pin Cable Detect Both Primary Secondary Auto Disabled Enabled Disabled 0, 5, 10, 15, 2. 0x, 2. 5x, 3. 0x, 3. 5x Host & Device Host Device Leave as Default. This setting toggles the detection of drives attached to the IDE controller Toggles the use of boot sector protection. Toggles the detection of 80wire IDE cables. 27 http://www. TYAN. com 3. 4 ­ Floppy Configuration Options related to floppy drives can be altered through the following. 360KB, 5 ¼" 1. 2MB, 5 ¼" 720KB, 3 ½" 1. 44MB, 3 ½" 2. 88MB, 3 ½" Disabled Enabled Disabled Enabled Disabled Defines the floppy drive type. Floppy A Floppy B Diskette Write Protect Floppy Drive Seek Toggles write protection. Toggles floppy drive seeking during POST. 3. 5 ­ Boot Settings Configuration Options related to startup settings can be altered through the following. Quick Boot Quiet Boot Add-On Rom Display Mode Boot up Num-Lock Boot up CPU Speed PS/2 Mouse Support Typematic Rate System Keyboard Enabled Disabled Enabled Disabled Force BIOS Keep Current On Off High Low Enabled Disabled Fast Slow Present Unavailable Enabled Disabled Enabled Disabled Enabled Disabled When set to Enabled, some self-tests will be skipped during POST. If set to Enabled, OEM logo will be displayed instead of POST messages. If Enabled, you will have to press F1 for the system to continue booting if an error is detected during POST. Toggles display of pressing DEL key to enter BIOS. Parity Check Wait for F1 if "error" Hit "Del" Message 28 http://www. TYAN. com 3. 6 ­ Super IO Configuration Options related to the IO interface can be altered through the following. Serial Port 1, 2 Address Onboard CIR Port Parallel Port Address Enabled Disabled Auto Enabled Disabled 3F8, 2F8 3E8, 2E8 Output Only Bi-directional EPP ECP Toggles use of serial ports 1 and or 2. Enabling ports also requires you to enter the I/O address for that port unless you select Auto. Two-way protocol Enhanced Parallel Port may provide higher bandwidth if an EPP compliant device is used (e. g. Enhanced Compatibility Port may provide higher bandwidth if an ECP compliant device is used (e. g. These options appear when the parallel port is set to Enabled. Parallel Port Mode Parallel Address 378 278 3BC 3. 7 ­ Onboard Device Configuration Options related to onboard devices can be altered through the following. Onboard ATI RageXL Video Onboard 82550 Onboard 82544GC Onboard SCSI Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Toggles the onboard ATI video graphics. Toggles the onboard SCSI controller. 3. 8­ USB Configuration Options related to USB can be altered through the following. USB Function Legacy USB Support Enabled Disabled Enabled Disabled Auto Enabled Disabled Auto Enabled Disabled Toggles the onboard USB ports. Toggles the use of onboard USB ports in DOS. USB Zip Emulation Type USB Beep Message Toggles Zip drive emulation on USB ports when in use. [. . . ] Standby mode: in this mode, the video and hard drives shut down; all other devices continue to operate normally. Striping: see RAID UltraDMA-33/66/100: a fast version of the old DMA channel. Without proper UltraDMA controller, your system cannot take advantage of higher data transfer rates of the new UltraDMA/UltraATA hard drives. This one port type can function as a serial, parallel, mouse, keyboard or joystick port. [. . . ]