User manual TYAN THUNDER K8SD PRO

[. . . ] Thunder K8SD Pro /// S2882-D Revision 1. 00 Copyright © TYAN Computer Corporation, 2001-2005. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. AMD, Opteron, and combinations thereof are trademarks of AMD Corporation. [. . . ] Set No for operating systems that do not meet the Plug and Play specifications. This setting controls how many PCI clocks each PCI device can hold the bus before another PCI device takes over. When set to higher values, every PCI device can conduct transactions for a longer time and thus improve the effective PCI bandwidth. This is the default setting and should not be changed unless the VGA card manufacturer requires Palette Snooping to be Enabled. ENABLED: BIOS uses PCI bus mastering for reading / writing to IDE drives. Allows user to reserve a specific IRQ for a legacy device (Note: most hardware devices & OS used do not support manual assigned). Allows user to reserve a specific DMA for a legacy device. Yes Plug & Play OS No PCI Latency Timer 32 64 96 128 160 192 224 248 Ascent PCI Bus Scan Order Descent Allocate IRQ to PCI VGA Yes No Disabled Palette Snooping Enabled PCI IDE Bus Master Disabled Enabled Available IRQ3 ~ IRQ15 Reserved DMA0 ~ 7 Available Reserved 56 http://www. TYAN. com 3. 06 ­ BIOS Boot Settings Menu You can display Boot Setup option by highlighting it using the Arrow (á/â) keys and pressing Enter. Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit Boot Settings 4 Boot Settings Configuration 4 Boot Device Priority 4 Hard Disk Drives 4 Removable Drives 4 ATAPI CDROM Drives Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit 3. 06. 1 ­ Boot Settings Configuration Sub-Menu Use this screen to select options for the Boot Settings Configuration. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit Boot Settings Configuration Quick Boot Quiet Boot Add On ROM Display Mode Boot up Num-Lock PS/2 Mouse Support Typematic Rate Floppy Error Report Keyboard Error Report Boot To OS/2 Wait for `F1' If Error Hit `DEL' Message Display Interrupt 19 Capture [Disabled] [Disabled] [Force BIOS] [On] [Enabled] [Fast] [Disabled] [Disabled] [No] [Enabled] [Enabled] [Disabled] Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit 57 http://www. TYAN. com Feature Boot Settings Configuration Quick Boot Mode Quiet Boot Add On ROM Display Mode Boot up Num-Lock PS/2 Mouse Support Typematic Rate Keyboard Error Report Floppy Error Report Boot To OS/2 Wait for `F1' If Error Option Description Enabled Disabled Disabled Enabled Force BIOS Keep Current On Off Enabled Disabled Fast Slow Disabled Enabled Disabled Enabled No Yes Enabled Disabled Enabled Disabled Disabled Enabled This option allows user bypass BIOS self test during POST. Allows user to force BIOS/Option ROM of add on cards to be displayed during quiet boot. Allows user to disable the "Press F1 to Continue" error message when error is detected. Allows user to disable the "Press DEL to enter setup" message during POST. Allows devices (such as network card) to capture INT19 for booting. Hit `DEL' Message Display Interrupt 19 Capture 58 http://www. TYAN. com 3. 06. 2 ­ Boot Device Priority Sub-Menu Use this screen to select options for the Boot Device Priority. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit Boot Device Priority 1st Boot Device [1st FLOPPY DRIVE] Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit Feature Boot Device Priority 1st Boot Device Option 1st FLOPPY DRIVE Disabled Description Settings for boot priority. These can be customized depending on your preference. 59 http://www. TYAN. com 3. 06. 3 ­ Hard Disk Drives Sub-Menu Use this screen to select options for the Hard Disk Drives. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit Hard Disk Drives 1st Drive [xx, xxx-xxxxx:xxx] Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. [. . . ] As long as a standby power comes into the system, SMDC will begin looking after the system. Tyan SMDC provides diversified methods to communicate with the hardware. IT manager has the flexibility to choose among Keyboard Controller Style (KCS), Block Transfer (BT) style, Intelligent Chassis Management Bus (ICMB), Intelligent Platform Management Bus (IPMB), Emergency Management Port (EMP) and standard IPMI-Over-LAN communication as defined in latest IPMI 1. 5 specification. Tyan SMDC is compatible with all IPMI-compliance software as well as Tyan System OperatorT M (TSO) software package. [. . . ]