User manual TYAN TOMCAT I7210

[. . . ] Tomcat i7210 S5112 User's Manual Tomcat i7210 /// Revision 1. 00 S5112 Copyright © TYAN Computer Corporation, 2004. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN, Tomcat, i7210 and S5112 are trademarks of TYAN Computer Corporation. [. . . ] Enabled / Disabled Onboard VGA Ctrl: This item allows you to "Enable" or "Disable" onboard VGA Ctrl function. Enabled / Disabled Onboard Lan Ctrl: This item allows you to "Enable" or "Disable" onboard 82541 Lan Ctrl function. Enabled / Disabled Onboard Sil3114 Ctrl: This item allows you to "Enable" or "Disable" onboard 3114 Ctrl function. Enabled / Disabled CSA LAN (GbE LAN): This item allows you to "Enable" or "Disable" CSA LAN GbE-LAN function. Enabled / Disabled On board GbE Lan Boot ROM: This item allows you to "Enable" or "Disable" On board GbE Lan Boot ROM function. Enabled / Disabled 3-16 http://www. tyan. com Tomcat i7210 S5112 Super IO Controller: Phoenix ­ AwardBIOS CMOS Setup Utility Super IO Device Onboard FDC Controller Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select RxD, TxD Active IR Transmission Delay UR2 Duplex Mode Onboard Parallel Port Parallel Port Mode EPP Mode Select ECP Mode Use DMA ICH Serial Port 1 ICH Serial Port 1 Use IRQ ICH Serial Port 2 ICH Serial Port 2 Use IRQ [Enabled] [3F8 / IRQ4] [2F8 / IRQ3] [Normal] [Hi, Lo] [Enabled] [Half] [378 / IRQ7] [SPP] [EPP1. 7] [3] [3E8] [IRQ10] [2E8] [IRQ11] Chapter 3: BIOS Setup Item Help _________________________ Menu Level : Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Onboard FDC Controller: Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install and-in FDC or the system has no floppy drive, select "Disabled" in the field. Enabled / Disabled Onboard Serial Port 1 / 2: Select an address and corresponding interrupt for the first and second serial ports. 3F8/IRQ4 / 2E8/IRQ3 / 3E8/IRQ4 / 2F8/IRQ3 / Disabled / Auto UART Mode Select: This field allows the users to configure what IR mode the 2nd serial port should use. Normal / IrDA and ASKIR RxD, TxD Active: This field configures the receive and transmit signals generated from the IR port. Hi, Hi / Hi, Lo / Lo, Hi / Lo, Lo IR Transmission Delay: This item allows you to "Enabled" or Disabled" the IR transmission delay. Enabled / Disabled UR2 Duplex Mode: This item allows you to select IR "Half" or "Full" duplex function. Half / Full Onboard Parallel Port: This field allows the user to configure the LPT port. 3-17 http://www. tyan. com Tomcat i7210 S5112 378/IRQ7 / 278/IRQ5 / 3BC/IRQ7 / Disabled Parallel Port Mode: This field allows the user to select the parallel port mode. SPP / EPP / ECP / ECP+EPP Chapter 3: BIOS Setup EPP Mode Select: This item allows you to determine the IR transfer mode of onboard I/O chip. EPP1. 9 / EPP1. 7 ECP Mode Use DMA: This field allows the user to select the DMA1 or DMA3 for the ECP mode. DMA1 / DMA3 ICH Serial Port 1: Select an address for the ICH first serial ports. Disabled/3F8/2F8/3E8/2E8 ICH Serial Port 1 Use IRQ: Select a corresponding interrupt for the ICH first serial ports. IRQ10/IRQ11/IRQ3/IRQ4/IRQ5/IRQ7 ICH Serial Port 2: Select an address for the ICH second serial ports. Disabled/3F8/2F8/3E8/2E8 ICH Serial Port 2 Use IRQ: Select a corresponding interrupt for the ICH second serial ports. IRQ10/IRQ11/IRQ3/IRQ4/IRQ5/IRQ7 Watch Dog Timer Select: This item allows the user to select after how long time the system will reboot. Disabled / 1 Min / 2 Min / 4 Min / 8 Min / 15 Min / 30 Min / 1 Hour 3-18 http://www. tyan. com Tomcat i7210 S5112 Chapter 3: BIOS Setup 3. 6 ­ Power Management Setup Options related to power management can be altered through the following: Phoenix ­ AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function ACPI Suspend Type Power Management Video Off Method Video Off In Suspend Suspend Type MODEN Use IRQ Suspend Mode HDD Power Down Intruder# Detection CPU THRM-Throttling Power On Setup Reload Global Timer Events Intruder# Detection [Enabled] [S1 (POS)] [User Define] [DPMS] [Yes] [Stop Grant] [3] [Disabled] [Disabled] [Disabled] [50. 0%] [Press Enter] [Press Enter] [Disabled] Item Help _________________________ Menu Level : Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults ACPI Function: Toggles advanced power and configuration done by OS. [. . . ] BMC is a standalone mini-CPU and runs on its own Real Time Operating System (RTOS) to complete all different kinds of tasks. Backed by Qlogic's ARM7 technology, IT manager can rest assure his server machines are always taken care. Unlike regular peripheral card such as AGP card, Network card or SCSI card, SMDC does not require any hardware specific driver. As long as a standby power comes into the system, SMDC will begin looking after the system. [. . . ]