User manual TYAN TOMCAT K8S

[. . . ] Tomcat K8S /// Revision 1. 01 S2850 Copyright © TYAN Computer Corporation, 2003. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. AMD, AMD Opteron, and combinations thereof, are trademarks of Advanced Micro Devices, Inc. [. . . ] +/Tab F1 F10 ESC Change Field Select Field Help Save and Exit Exit 37 http://www. TYAN. com Feature Remote Access Terminal Type Serial Port Number Serial Port Mode Flow Control Post-Boot Support Option Disabled Serial ANSI VT100 COM1 COM2 115200 8n1 57600 8n1 19200 8n1 9600 8n1 Hardware None Disabled Enabled Description Enables remote access to system through serial port Sets the type of terminal used for remote access Determines which serial port will be used for remote access Sets the speed of data to terminal Enables hardware flow control to protect buffer overflow Keeps redirection active after booting to DOS 3. 04. 7 ­ USB Configuration Sub-Menu You can use this screen to view the USB Configuration Menu. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit USB Configuration USB Devices Enabled : Legacy USB Support USB Beep Message [Auto] [Disabled] Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. +/Tab F1 F10 ESC Change Field Select Field Help Save and Exit Exit Feature USB Devices Enabled Option Description USB Devices detected Legacy USB Support Auto Disabled Enabled Floppy Hard Disk Disabled Enabled Enables support for legacy USB devices such as keyboards, mice, & bootable USB devices Enables beep during USB Device Enumeration USB Beep Message 38 http://www. TYAN. com 3. 04. 8 Onboard Device Sub-Menu You can use this screen to view Device & PCI Slot Configuration Menu. This menu allows the user to enable or disable integrated devices, option ROM, and PCI cards added. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit Onboard Devices Configuration Onboard ATI Video Onboard LAN1 Onboard LAN2 Onboard Serial ATA Onboard Devices Optrom Configuration Onboard LAN 1 Option Rom Onboard LAN 2 Option Rom Serial ATA Option Rom Feature Option Enabled Disabled Enabled Disabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. +/- Change Field Tab Select Field F1 Help F10 Save and Exit ESC Exit Description Allows user to enable or disable onboard ATI video, Serial ATA controller, and Onboard LAN individually Allows user to enable or disable onboard ATI video, Serial ATA controller, and Onboard LAN Option Rom individually Onboard Devices Configuration Onboard ATI Video, LAN1, LAN2, & Serial ATA Onboard LAN1, LAN2, & Serial ATA Option Rom 3. 04. 9 Watchdog Timer Sub-Menu You can use this screen to view Watchdog Timer Configuration Menu. Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit Watchdog Timer Configuration Watchdog Timer Timer-Out Value(minutes): Enabled 2 Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. +/- Change Field Tab Select Field F1 Help F10 Save and Exit ESC Exit 39 http://www. TYAN. com Feature Option Description Allows user to enable or disable Watchdog timer Watchdog Timer Configuration Watchdog Timer Disabled Enabled 2 4 Timer-Out Value(minutes) 6 8 10 Allows user to select Watchdog timer 3. 05 ­ BIOS PCI/PnP Menu You can use this screen to view PnP (Plug & Play) BIOS Configuration Menu. This menu allows the user to configure how the BIOS assigns resources & resolves conflicts. Use the Plus and Minus (+/-) keys to change the value of the selected option. The settings are described on the following pages. Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit PCI/PnP Setting Plug & Play OS PCI Latency Timer Allocate IRQ to PCI VGA Palette Snooping PCI IDE BusMaster IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ14 IRQ15 DMA Channel_0 DMA Channel_1 DMA Channel_3 DMA Channel_5 DMA Channel_6 DMA Channel_7 Reserved Memory Size [No] [64] [Yes] [Disabled] [Disabled] [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Disabled] Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. +/Tab F1 F10 ESC Change Field Select Field Help Save and Exit Exit 40 http://www. TYAN. com Feature PCI PnP Configuration Option Yes Description The Yes setting allows the operating system to change the interrupt, I/O, and DMA settings. Set this option if the system is running Plug and Play aware operating systems. Set No for operating systems that do not meet the Plug and Play specifications. This setting controls how many PCI clocks each PCI device can hold the bus before another PCI device takes over. When set to higher values, every PCI device can conduct transactions for a longer time and thus improve the effective PCI bandwidth. This is the default setting and should not be changed unless the VGA card manufacturer requires Palette Snooping to be Enabled. Allows user to reserve a specific IRQ for a legacy device (Note: most hardware devices & OS used do not support manual assigned ) Allows user to reserve a specific DMA for a legacy device Allows user to reserve a specific size in memory for a legacy device Allows user to reserve a specific address in memory for a legacy device Plug & Play OS No 96 128 160 192 224 248 Allocate IRQ to PCI VGA Yes No Disabled Enabled Available IRQ3 ~ IRQ15 Reserved Available Reserved Disabled 16K ~64K Disabled C0000 ~ DC000 PCI Latency Timer Palette Snooping DMA0 ~ 7 Reserved Memory Size Reserved Memory Address 3. 06 ­ BIOS Boot Menu You can display Boot Setup option by highlighting it using the Arrow ( / ) keys and pressing Enter. The settings are described on the following pages. 41 http://www. TYAN. com Main Advanced PCI/PnP BIOS Setup Utility Boot Security Chipset Power Exit Boot Setting Boot Settings Configuration Boot Device Priority Removable Drives Use [ENTER], [TAB] or [SHIFT_TAB] to select a field Use [+] or [-] to configure system time. +/Tab F1 F10 ESC Change Field Select Field Help Save and Exit Exit 3. 06. 1 ­ Boot Settings Configuration Sub-Menu Use this screen to select options for the Boot Settings Configuration. [. . . ] Standby mode: in this mode, the video and hard drives shut down; all other devices continue to operate normally. Without a proper UltraDMA controller, your system cannot take advantage of higher data transfer rates of the new UltraDMA/UltraATA hard drives. This one port type can function as a serial, parallel, mouse, keyboard or joystick port. It is fast enough to support video transfer, and is capable of supporting up to 127 daisy-chained peripheral devices. [. . . ]