User manual TYAN TRINITY 371

[. . . ] Trinity 371 Motherboard Users Manual Revision 1. 20 Tyan S1857 Copyright © Tyan Computer Corporation, 1999. No part of this manual may be reproduced or translated without prior written consent from Tyan Computer Corp. All registered and unregistered trademarks and company names contained in this manual are propery of their respective companies including, but not limited to the following. Information contained in this publication has been carefully checked for accuracy and reliability. [. . . ] Reserved Memory Size This option specifies the size of the memory area reserved for legacy ISA adapter cards. The settings are Disabled, 16K, 32K, or 64K. http://www. tyan. com 60 Reserved Memory Address This option specifies the beginning address (in hex) of the reserved memory area. The specified ROM memory area is reserved for use by legacy ISA adapter cards. This option does not appear if the Reserved Memory Size option is set to Disabled. The settings are C0000, C4000, C8000, CC000, D0000, D4000, D8000, or DC000. PCI Device Search Order This option changes the BIOS scan order of the PCI slot - from first to last or last to first. BIOS Devnode for Shadow RAM This option is used for some add-on card ROMs which do not claim the correct memory range that they occupy. The settings are Disabled or Enabled. BIOS S1857 Trinity 371 61 Chapter 3 BIOS Configuration Peripheral Setup Peripheral Setup options are displayed by choosing Peripheral Setup from the AMIBIOS Setup main menu. All Peripheral Setup options are described here. AMI BIOS EASY SETUP UTILITY Ver. 1. 16 (c)1998 American Megatrends, Inc. All Rights Reserved Advanced Advanced CMOS Setup Advanced Chipset Setup Power Management Setup Plug and Play Setup Peripheral Setup Change Language Setting [ Enter ] [ Enter ] [ Enter ] [ Enter ] [ Enter ] English Setup Help Configure PCI / Plug and Play features Previous Item Next Item Select Menu ESC:Exit Enter:Select F5:Setup Defaults F6:Original Values F10:Save & Exit Peripheral Setup Default Settings Chart Setting Option Overclo ck Warning M essage P o wer Lo ss Co ntro l Keybo ard Wake-up Functio n M o use Wake-up Functio n Slo t-1 Current Temperature P PGA 370 Current Temperature VCOREA VCORE +3. 3V VCORE +5V VCORE +12V VCORE -12V Fan1 Speed Optimal Default Fail-Safe Default Enabled A lwaays Off Disabled Disabled N/A N/A 1. 8 3. 24 +4. 97 +11. 79 -8. 40 3648 Enabled A lways Off Disabled Disabled N/A N/A 2. 01 2. 00 3. 34 +5. 02 +11. 91 N/A http://www. tyan. com 62 Settings Chart (Continued) Setting Option Fan2 Speed Onbo ard FDC Onbo ard Serial P o rt 1 Onbo ard Serial P o rt 2 Serial Po rt 2 M o de *IR Duplex M o de Onbo ard P arallel P o rt P arallel Po rt M o de *EP P Versio n P arallel Po rt IRQ *Parallel Po rt DM A Channel Onbo ard IDE Optimal Default Fail-Safe Default N/A Enabled 3F8h 2F8h No rmal N/A 378 ECP N/A 7 3 B o th N/A Enabled 3F8h 2F8h No rmal N/A 378 ECP N/A 7 3 B o th BIOS * Setting Option not selectable Note: The CPU fan activates after the VGA card is initalized and not when the system boots up, therefore you may experience a 5 second delay before the CPU fan is enabled. Overclock Warning Message When enabled, this option sends a warning message if the CPU is overclocked. Keyboard Wake-up Function This option allows for system power-on via the keyboard. Mouse Wake-up Function This option allows for system power-on via the Mouse. Onboard FDC Set this option to Enabled to enable the floppy drive controller on the motherboard. The settings are Auto, Enabled, or Disabled. S1857 Trinity 371 63 Chapter 3 BIOS Configuration Onboard Serial Port1 This option specifies the base I/O port address of serial port 1. Onboard Serial Port2 This option specifies the base I/O port address of serial port 2. Serial Port2 Mode This option specifies the operating mode for serial port 2. This option will not appear if the Onboard Serial Port2 option is set to Disabled, or is set to Auto and your system does not have an onboard serial port 2. IR Transmission Mode This option specifies the infrared transmission method. This option will not appear if the Serial Port2 Mode option is set to Normal. The settings are Full or Half. M ode Full D uple x D e s cription Data is transmitted in two directions at once. Any data you send will not appear on your screen until it has been received by the other device and sent back to you. [. . . ] You can access this feature by pressing <F5> while the Starting MS-DOS. . . If you are uncertain whether or not you have a memory manager running, try FMW. If you see a warning message about the CPU mode, follow the above directions to get around the memory manager. You can copy the contents of the Flash directory to your hard drive, or you can run the utility from a backup of the support floppy disk. [. . . ]