User manual VIEWSONIC CDP4235

[. . . ] CDP3235 CDP4235 CDP4235-T CDP4635 CDP4635-T CDX5550-L User Guide IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http:// box in the upper right corner of our website. "Antes de operar su equipo lea cu idadosamente las instrucciones en este manual" Model No. VS14694/VS14693/VS14709/VS14692/VS14710VS14691 i Compliance Information For U. S. A. [. . . ] The following zoom modes are available for: PC mode: {FULL} / {NORMAL} / {CUSTOM} / {REAL}. Video mode: {FULL} / {NORMAL} / {DYNAMIC} / {CUSTOM} / {REAL}. FULL This mode restores the correct proportions of pictures transmitted in 16:9 using the full screen display. NORMAL The picture is reproduced in 4:3 format and a black band is displayed on either side of the picture. 4. 2. 2. SCREEN menu SCREEN AUTO SETUP AUTO ADJUST H POSITION V POSITION CLOCK CLOCK PHASE ZOOM MODE CUSTOM ZOOM H RESOLUTION V RESOLUTION INPUT RESOLUTION SCREEN RESET OFF 50 50 2200 66 FULL 1920 1080 DYNAMIC Fill the entire screen by stretching 4:3 pictures non-proportionally. CUSTOM Choose to apply the custom zoom settings in the Custom Zoom submenu. 1 2 3 PIP REAL This mode displays the image pixelby-pixel on screen without scaling the original image size. :SEL SET :NEXT EXIT :RETURN MENU :EXIT MENU CUSTOM ZOOM You can use this function to further customize the zoom settings to suit the image you want to display. NOTE: This item is functional only when the {ZOOM MODE} setting is set to {CUSTOM}. AUTO SETUP Use this function to let the display automatically optimize the display of VGA input image. AUTO ADJUST Choose to let the display detect and display available signal sources automatically. {ON} - Set the display to display the image automatically once a signal is connected. H POSITION Press the [ ] button to move the image to the right, or [ ] to move the image to the left. ZOOM Expands the horizontal and vertical sizes of the image simultaneously. H ZOOM Expands the horizontal size of the image only. 16 V ZOOM Expands the vertical size of the image only. 4. 2. 4. PIP menu PIP H POSITION Moves the horizontal position of the image left or right. V POSITION Moves the vertical position of the image up or down. PIP 1 2 3 PIP MODE PIP SIZE PIP AUDIO PIP H POSITION PIP V POSITION SUB INPUT PIP RESET OFF SMALL MAIN AUDIO 100 0 VIDEO INPUT RESOLUTION Set the resolution of the VGA input. This is only required when the display is unable to detect the VGA input resolution correctly. The options are: {1024x768 / 1280x768 / 1360x768} {1400x1050 / 1680x1050} {1600x1200 / 1920x1200} {Auto}: Determines the resolution automatically. The selected settings will become effective after turning off the power and turn it on again. SCREEN RESET Reset all settings in the SCREEN menu to factory preset values. :SEL SET :NEXT EXIT :RETURN MENU :EXIT MENU PIP MODE Select the PIP (Picture-in-Picture) mode. PIP SIZE Select the size of the sub picture in the PIP (Picture-in-Picture) mode. PIP AUDIO Select the audio source in the PIP (Picture-in-Picture) mode. {MAIN AUDIO} - Select audio from the main picture {SUB AUDIO} - Select audio from the sub picture. AUDIO menu AUDIO BALANCE TREBLE BASS AUDIO RESET 50 50 50 Adjust the horizontal placement of the sub picture. PIP RESET Reset all settings in the PIP menu to factory preset values. NOTES: 1 2 3 PIP :SEL SET :NEXT EXIT :RETURN MENU :EXIT MENU The PIP function is available only for certain signal source combinations as shown in the table below. The availability of the PIP function will also depend on the resolution of the input signal being used. Main Picture Sub Picture DVI VGA HDMI YPbPr S-Video Video Card OPS DVI X X X X O O X VGA HDMI YPbPr S-Video Video X X X X O O X X X X X O O X X X X X O O X O O O O X X O O O O O X X O Card OPS X X X X O O X BALANCE Adjust to emphasize left or right audio output balance. AUDIO RESET Reset all settings in the AUDIO menu to factory preset values. (O: PIP function available, X: PIP function unavailable) 17 By pressing the [PIP ON/OFF] button on the remote control, you can change the mode in the order shown below: PIP POP SBS ASPECT SBS FULL OFF SCHEDULE TODAY 1 2 3 4 5 6 7 2011 . 04 ON : EVERY DAY WED SAT EXIT THU 20 : 19 : 55 INPUT OFF : MON THU SUN :RETURN follows: PIP SIZE {SMALL} : 320 x 240 pixels {MIDDLE} : 480 x 320 pixels {LARGE} : 640 x 480 pixels POP SIZE : 474 x 355 pixels PIP sizes shown above irrespective of the aspect ratio of the input image. TUE FRI EVERY WEEK MENU :EXIT +-:SEL MENU 2. Press [ ] or [ ] button to select a schedule item (item number 1 ~ 7), and then press [SET] button to mark it the item number. SCHEDULE 4. 2. 5. [. . . ] How to get service: For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support page). You will need to provide your product's serial number, so please record the product information in the space provided below on your purchase for your future use. Please retain your receipt of proof of purchase to support your warranty claim. For Your Records Product Name: ________________________ Document Number: _____________________ Purchase Date: ________________________ Model Number: _____________________________ Serial Number: _____________________________ Extended Warranty Purchase? [. . . ]