User manual VIEWSONIC PJD5223

[. . . ] PJD5223 DLP Projector User Guide IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://www. viewsonic. com in English, or in specific languages using the Regional selection box in the upper right corner of our website. "Antes de operar su equipo lea cu idadosamente las instrucciones en este manual" Compliance Information FCC Statement This device complies with part 15 of FCC Rules. [. . . ] See "Connecting Video source devices" on page 17 for 18 EN-18 details. Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused composite Video output sockets available: If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. Take a Video cable and connect one end to the composite Video output socket of the Video source device. Connect the other end of the Video cable to the VIDEO socket on the projector. Important If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. You need only connect to this device using a composite Video connection if Component Video and S-Video inputs are unavailable for use. See "Connecting Video source devices" on page 17 for details. 19 EN-19 Operation Powering On/Off the Projector Powering On the Projector: 1. Complete the AC power cord and peripheral signal cable(s) connections. If you are connecting multiple sources to the projector simultaneously, press SOURCE on the projector or Source on the remote control to select your desired signal or press your desired signal key on the remote control. When green mode is turned off, the Power LED begins flashing and the projector has entered stand-by mode. When green mode is turned on, the Power LED becomes steady light and the projector has entered stand-by mode. If you want to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered stand-by mode. Disconnect the AC power cord from the electrical outlet and the projector. Do not turn on the projector right after power off. Powering Off the Projector: 1. 4. 20 EN-20 Adjusting the Projector Height The projector is equipped with an elevator foot to adjust the image height. To raise or lower the image, turn the elevator foot to fine-tune the height. To avoid damaging the projector, make sure that the elevator foot is fully retracted before placing the projector in its carrying case. Adjusting the Projector Zoom and Focus 1. Adjust the image size by rotating the zoom ring. 21 EN-21 Adjusting Projection Image Size Refer to the graphic and table below to determine the screen size and projection distance. Maximum zoom Minimum zoom Screen Center of lens Vertical offset Projection distance Image height [inch (cm)] 18 (45. 72) 36 (91. 44) 48 (121. 92) 60 (152. 4) 90 (228. 6) 120 (304. 8) 150 (381. 0) 180 (457. 2) Screen size Diagonal [inch (cm)] 30 (76) 60 (152) 80 (203) 100 (254) 150 (381) 200 (508) 250 (635) 300 (762) 4 : 3 Screen Projection distance [inch (m)] (min. zoom) 45. 3 (1. 2) 92. 2 (2. 3) 123. 5 (3. 1) 154. 8 (3. 9) 233. 0 (5. 9) 311. 2 (7. 9) 389. 4 (9. 9) 467. 6 (11. 9) (max. zoom) 50. 6 (1. 3) 102. 9 (2. 6) 137. 7 (3. 5) 172. 5 (4. 4) 259. 6 (6. 6) 346. 7 (8. 8) 433. 8 (11. 0) - Vertical offset [inch (cm)] 2. 70 (6. 86) 5. 40 (13. 72) 7. 20 (18. 29) 9. 00 (22. 86) 13. 50 (34. 29) 18. 00 (45. 72) 22. 50 (57. 15) 27. 00 (68. 58) Position the projector in a horizontal position; other positions can cause heat build-up and damage to the projector. Smoke residue may buildup on critical parts and damage the projector or its performance. Consult with your dealer for special installation such as suspending from a ceiling. 22 EN-22 Locking control keys With the control keys on the projector locked, you can prevent your projector settings from being changed accidentally (by children, for example). When the Panel Key Lock is on, no control keys on the projector will operate except Power. [. . . ] Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, unauthorized attempted repair, or failure to follow instructions supplied with the product. Causes external to the product, such as electrical power fluctuations or failure. Any product exhibiting a condition commonly known as "image burn-in" which results when a static image is displayed on the product for an extended period of time. How to get service: For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support page). [. . . ]