User manual VIEWSONIC VA503B

[. . . ] : VS11357 Contents TCO Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Compliance Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Copyright Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ViewSonic recommends that you install both the INF and ICM files. Precautions · Sit at least 18" from the LCD display. · Avoid exposing the LCD display to direct sunlight or another heat source. Do not place anything on the LCD display that prevents heat dissipation. · Ensure the area around the LCD display is clean and free of moisture. · Do not place heavy objects on the LCD display, video cable, or power cord. · If smoke, an abnormal noise, or a strange odor is present, immediately switch the LCD display off and call your dealer or ViewSonic. · Do not rub or apply pressure to the LCD panel, as it may permanently damage the screen. ViewSonic VA503b 4 Quick Installation 1. Connect video cable · Make sure both the LCD display and computer are turned OFF · Remove rear panel covers if necessary · Connect the video cable from the LCD display to the computer Macintosh users: Models older than G3 require a Macintosh adapter. Attach the adapter to the computer and plug the video cable into the adapter. To order a ViewSonic® Macintosh adapter, contact ViewSonic Customer Support. Turn ON LCD display and computer Turn ON the LCD display, then turn ON the computer. NOTE: Windows users may receive a message asking them to install the INF file. After setting the timing mode, use the OSD (On-screen Display) controls to adjust the screen image. For the best picture quality set your LCD display timing mode to: VESA 1024 x 768 @ 60Hz. Set the resolution: Right-click on the Windows desktop > Properties > Settings > set the resolution. Set the refresh rate: See your graphic card's user guide for instructions. WARNING: Do not set the graphics card in your computer to exceed the maximum refresh rate of 85Hz; doing so may result in permanent damage to your LCD display. OSD and Power Lock Settings · OSD Lock: Press and hold [1] and the up arrow for 10 seconds. If any buttons are pressed the message OSD Locked will display for 5 seconds. · OSD Unlock: Press and hold [1] and the up arrow again for 10 seconds. · Power Button Lock: Press and hold [1] and the down arrow for 10 seconds. If the power button is pressed the message Power Button Locked will display for 5 seconds. With or without this setting, after a power failure, your LCD display's power will automatically turn ON when power is restored. [. . . ] · NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE. If the screen still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen. If the case still not clean, apply a small amount of a non-ammonia, non-alcohol based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface. Disclaimer · ViewSonic® does not recommend the use of any ammonia or alcohol-based cleaners on the LCD display screen or case. [. . . ]