User manual VIVITAR VIVICAM 3945S

[. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Afterwards, you may review the sequence of images to select the best one. Use t h e / b u t t o n s to select ], then press the OK [CONTINUOUS button. Capturing will stop when the shutter button is released. PICTURE FUNCTION SETUP User's Manual >> ISO CAPTURE MODE SELECT PAGE: SELECT ITEM: [S] EXIT: ENTRY: CAPTURE MODE SINGLE CONTINUOUS AEB BACK : A S SET : Maximum number of continuous shots: 5. In CONTINUOUS mode, the flash mode will be set to NO FLASH automatically. EN-35 Auto-Exposure Bracketing (AEB) Auto-exposure bracketing is an effective technique when it is difficult to determine the precise exposure of a scene. Using AEB the ViviCam 3945s will capture a sequential burst of three images at three different exposure settings. Afterwards, you may review the sequence of images to select the best exposure. Slide the mode switch to [ ]. PICTURE FUNCTION SETUP EN-36 Digital Camera >> 2. Press the shutter button to capture images. ISO CAPTURE MODE SELECT PAGE: SELECT ITEM: [S] EXIT: ENTRY: CAPTURE MODE SINGLE CONTINUOUS AEB BACK : A S SET : In AEB mode, the flash mode will be set to NO FLASH automatically. Adjusting White Balance Manually Manual white balance lets you configure the digital still ViviCam 3945s for a particular light source and other conditions. Note that you must perform manual white balance under the same conditions you will be shooting. You must also have a piece of white paper or other similar object on hand in order to perform this function. Point the ViviCam 3945s at an enclosed gray card for which you can set the white balance. U s e t h e / buttons to select [EXECUTE], then press the OK button to confirm. To exit from the menu, press the button. PICTURE FUNCTION Q R GB User's Manual >> SETUP WB WB MANUAL WB SELECT ITEM: CANCEL EXIT: ENTRY: MANUAL WB EXECUTE CANCEL BACK : SET : EN-37 PLAYBACK MODE - THE BASICS In the playback mode, you can view, magnify, delete images, play video clips , or run a slide show. This mode also provides a thumbnail image display, allowing you to quickly search for the desired image. EN-38 Digital Camera >> Viewing Images 1. Pressing the / buttons during image playback will rotate the image 90 degrees. The button rotates the image clockwise, whereas the button rotates the image counterclockwise. 90 o Counterclockwise 0 (Original) o 90 Clockwise o If there is no image stored in the internal memory or memory card, [NO PICTURE] message will appear on the monitor. Pressing the button while playing back images changes the LCD display in the sequence of: Standard display Detailed display No information. Magnifying Images While reviewing your images, you may enlarge a selected portion of an image. Images that are being displayed can be enlarged in 8 times enlargement. To view different portion of the images, press the / / / buttons to adjust the display area. The white frame indicates the entire image, while the pink box shows the location of the currently enlarged area. To return to regular display, toggle the W button until the regular display appears on the screen. User's Manual >> EN-39 The range of magnification factor is: 1. 5x, 2. 0x, 2. 5x, 3. 0x, 3. 5x, 4. 0x, 4. 5x, 5. 0x, 5. 5x, 6. 0x, 6. 5x, 7. 0x, 7. 5x and 8. 0x. Thumbnail Display (Index Playback) This function allows you to view four or nine thumbnail images on the LCD monitor simultaneously so you may search for a particular image. Use the / buttons to choose the desired number of thumbnail images to be displayed, then press the OK button. [. . . ] Item Image sensor Image resolution EN-67 User's Manual >> TROUBLESHOOTING Refer to the symptoms and solutions listed below before sending the ViviCam 3945s for repairs. If the problem persists, contact your local reseller or service center. EN-68 Digital Camera >> Power Supply Cause Symptom The power does not The battery is not loaded. come on. The power cuts out during use. The power does not go off. The battery runs out quickly. The battery or ViviCam 3945s feels warm. Solution Load the battery correctly. [. . . ]