User manual WACOM CINTIQ 21UX

[. . . ] Installation Guide & Hardware Manual for Cintiq 21UX (DTZ-2100D) Wacom Cintiq® 21UX Installation Guide & Hardware Manual for Cintiq 21UX (DTZ-2100D) English version 2. 2, November 05, 2007 Copyright Wacom Co. , Ltd. , 2007 All rights reserved. No part of this manual may be reproduced except for your express personal use. Wacom reserves the right to revise this publication without obligation to provide notification of such changes. Wacom does its best to provide current and accurate information in this manual. [. . . ] User settings: When you manually adjust the display using the OSD function, the settings are stored within Cintiq for use the next time the unit receives a similar signal. Color calibration: Changing the color, color temperature, contrast, brightness, or backlight from their default settings will invalidate the ICC color profile that was included on the driver CD. ON SCREEN DISPLAY (OSD) SETTINGS The OSD function enables you to adjust and optimize a variety of display settings at the touch of a button. Simply reach over the top of the display unit to locate the buttons with your fingers. Note: Braille-style dots above the buttons help you to identify each one by touch. Digital/Analog (DVI/VGA) switch MENU / ENTER button Use this button to open the OSD menu and to accept changes you make to the OSD settings. Up or Down buttons Press the up or down buttons to toggle between menu options, and to increase or decrease the value of a selected setting. SELECT / AUTO button When working with the OSD menu, pressing SELECT chooses the highlighted menu option. In VGA mode with the OSD menu closed, pressing AUTO performs an AUTO ADJUST of the display. Customizing Page 35 The basic process for working with the OSD is as follows: · · Press the MENU button to open the OSD main menu. Then press the SELECT button to choose the highlighted icon. The Main Control icon displays a DVI or VGA identifier, depending on which video interface is currently in use. · Press the up or down buttons to toggle between menu options. Note that some options, such as POSITION, are not available when in DVI mode. · Press the up or down buttons to select a setting for adjustment. Press the ENTER button to accept your changes. Note: After changing a setting, the OSD menu will automatically close after a few moments of inactivity. You can also continue to press ENTER in order to back out of the OSD menu. If you make changes to the display appearance and cannot return to the original settings, go to the RESET menu and select the FACTORY RESET option to return Cintiq to its original factory defaults. · · See the following pages for details about the OSD menu options. Customizing Page 36 When you open the On Screen Display, the main menu icons are displayed. Main Control. Provides options (DISPLAY, IMAGE, POSITION, and COLOR) that enable you to fine tune your display settings. Returns the display parameters of the current mode to their factory default settings. Language. Allows you to choose the language in which the OSD menu will be displayed. DISPLAY menu options are as follows: · BRIGHTNESS. Increases or decreases the backlight brightness level. IMAGE menu options are as follows: · SCALING. Enables you to choose how the image is displayed when working at resolutions below 1600 x 1200. ASPECT resizes the image to fill as much of the screen as possible while maintaining the correct aspect ratio. (VGA only. ) Choose this function to automatically optimize the display screen image. (VGA only. ) Synchronizes the signal timing of the pen display to that of your graphics card. Use this adjustment when you experience an unstable or flickering image, or horizontal distortion lines. (VGA only. ) Changes the display data frequency to match that of your graphics card. Use this adjustment when you experience an unstable or flickering image, or vertical distortion lines. Customizing Page 37 POSITION menu options (VGA only) are as follows: · VERTICAL. To automatically adjust, use the AUTO ADJUST option. COLOR menu options are as follows: · TEMPERATURE. [. . . ] You should send the product, shipping charges prepaid, to the designated service location, accompanied by the return authorization number, your name, address and telephone number, proof of purchase date, and a description of the defect. Wacom will pay for return shipping by United Parcel Service or by an equivalent service as chosen by Wacom. Wacom's sole obligation and entire liability under this warranty shall be, at Wacom's option, either the repair or replacement of the defective product or parts thereof of which Wacom is notified during the Warranty Period; provided, however, that you are responsible for (i) the cost of transportation of the product to the designated service location and (ii) any loss or damage to the product resulting from such transportation. Wacom shall have no responsibility to repair or replace the product if the failure of the product has resulted from accident, abuse, misuse, negligence, or unauthorized modification or repair, or if it has been handled or stored other than in accordance with Wacom's storage instructions. [. . . ]