User manual WHIRLPOOL AMD 040 INSTRUCTION FOR USE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL AMD 040. We hope that this WHIRLPOOL AMD 040 user guide will be useful to you.


WHIRLPOOL AMD 040 INSTRUCTION FOR USE: Download the complete user guide (2089 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL AMD 040 MODE D'EMPLOI (2097 ko)
   WHIRLPOOL AMD 040 BRUGSVEJLEDNING (2183 ko)
   WHIRLPOOL AMD 040 BRUGSVEJLEDNING (2183 ko)
   WHIRLPOOL AMD 040 GEBRUIKSAANWIJZING (2095 ko)
   WHIRLPOOL AMD 040 BEDIENUNGSANLEITUNG (2094 ko)
   WHIRLPOOL AMD 040 INSTRUZIONI PER L'USO (2185 ko)
   WHIRLPOOL AMD 040 LIBRO DE INSTRUCCIONES (2185 ko)

Manual abstract: user guide WHIRLPOOL AMD 040INSTRUCTION FOR USE

Detailed instructions for use are in the User's Guide.

[. . . ] BEFORE USING THE APPLIANCE To make the most out of your new appliance, please read the user instructions carefully and keep them handy for future consultation. Before using the appliance please follow and set according to the below indications: Remote Control (RC) presetting: Each time the batteries are replaced in the remote control, the RC is pre-set on Heat pump. If the air conditioner that you purchased is a cooling only, then the pre-set on Heat pump will not bring any changes. Auto-Restart presetting Function: To set the auto-restart function, press the Emergency button (ON/OFF) on the indoor unit for at least 5 seconds A buzz sound will signal that the auto-restart function is set and the air conditioner is in standby. [. . . ] In SLEEP mode, • The appliance will stop operation automatically after operating for 8 hours. • Set temperature will rise by max 1°C if the appliance operates in cooling mode for 2 hours. iii) After the time set displayed for 5 seconds the clock will be displayed on the LCD of the remote control instead of set timer. How to cancel TIMER ON Press the TIMER ON button again, a "beep" can be heard and the indicator disappears, the TIMER ON mode has been canceled. Note: It is similar to set the TIMER OFF, you can make the appliance switch off automatically at your desired time. Unplug from the power supply Turn off the appliance first before disconnecting from power supply. Use lukewarm water (below 40°C) to clean if the appliance is very dirty. Never use substances such as gasoline or polishing powder to clean the appliance. Air filter It is necessary to clean the air filter after using it for about 100 hours. Clean the air filter every two weeks if the air conditioner operates in an extremely dusty environment. Unplug from the power supply Turn off the appliance first before disconnecting from power supply and remove the air filter. If the filter is very dirty, clean it with a solution of lukewarm water and neutral detergent. B PROTECTION Operating condition The protective device maybe trip and stop the appliance in the cases listed below. Outdoor air temperature is over 24°C HEATING Outdoor air temperature is below -7°C Room temperature is over 27°C Outdoor air temperature is over *43°C COOLING Room temperature is below 21°C DRY Room temperature is below 18°C *For Tropical (T3) Climate condition models, the temperature point is 52°C instead of 43°C. If the air conditioner runs in COOLING or DRY mode with door or window opened for a long time when relative humidity is above 80%, dew may drip down from the outlet. Noise pollution • Install the air conditioner at a place that can bear its weight in order to operate more quietly. 15 • Install the outdoor unit at a place where the air discharged and the operation noise would not annoy your neighbours. • Do not place any obstacles in front of the air outlet of the outdoor unit lest it increases the noise level. Protection device Wait at least 3 minutes before restarting the unit after operation stops or changing mode during operation. After connecting to power supply and turning on the appliance immediately, a delay of 20 seconds may occur before it starts to operate. Timer should be set again if it has been cancelled. Features of HEATING mode Preheating 2-5 minutes are necessary to preheat the indoor unit at HEATING operation start. Defrosting (out door unit) In HEATING operation the appliance will defrost (de-ice) automatically to raise efficiency. Note: Heating is NOT available for cooling only air conditioner models. TROUBLESHOOTING Operation problems are often due to minor causes that can be found and fixed without using any tools: Trouble Analysis • Is the protection device or fuse blown? [. . . ] In order not to disturb your neighbours and protect the environment, install a drain port and a drain hose to direct the condensate water. Just install the drain port and rubber washer on the chassis of the outdoor unit, then connect a drain hose to the port Washer as shown in the figure on the right . Install and Fix Outdoor Unit Drain hose Fix with bolts and nuts tightly on a flat and strong (prepare by user) floor. If installed on the wall or roof, make sure to fix the supporter well to prevent it from shaking due to serious vibration or strong wind. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL AMD 040




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL AMD 040 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.