User manual WHIRLPOOL AWM 9100/BS INSTRUCTION FOR USE

[. . . ] Normally soiled and sweaty sportswear made of cotton jersey or microfibres. This programme includes a prewash cycle - you can add detergent also to the prewash chamber. Blankets made of synthetic fibres, bedcovers filled with polyester or other artificial fibres, sleeping bags, bathmats and similar items. Curtains and delicate dresses, skirts, shirts and blouses. ❉ ❉ ❉ ❉ — — ❉ ❉ ❉ — — — — — — Yes ❉ ❉ ❉ ❉ ❉ ❉ — ❉ ❉ ❉ ❉ ❉ — ❉ — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — ❉ — — — ❉ — — ❉ — — — ❉ ❉ ❉ ❉ ❉ — ❉ ❉ ❉ ❉ ❉ ❉ — — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — ❉ — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — ❉ — ❉ ❉ ❉ ❉ — — ❉ ❉ ❉ — — ❉ — — — ❉ ❉ ❉ ❉ ❉ ❉ — — ❉ — — ❉ — — — ❉ ❉ ❉ ❉ — — — ❉ — — — ❉ — — — 1000 max. Yes 1000 20 to 60 Synthetics Kids wear Daily Express Sport Bulky Delicates Wool Handwash Whitest whites Gentle Spin Rinse & Spin Drain & Spin 1) 2) 5. 0 5. 0 5. 0 5. 0 4. 0 4. 0 4. 0 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 1000 20 to 60 1000 20 to 60 1000 20 to 60 1000 20 to 30 1000 20 to 60 1000 20 to 95 800 1) 20 to 40 1000 20 to 40 800 1) 20 to 30 1000 20 to 60 800 1) 1000 1000 ❉ — ❉ — ❉ ❉ ❉ — ❉ — ❉ — ❉ ❉ Only woollens, labelled with the Woolmark and identified as machine washable. [. . . ] When a programme sequence is finished, the corresponding symbol goes off. Due to variations in load and temperature of inlet water, the remaining time is newly calculated in certain programme phases. If this is the case, an animation appears on the display and the and the “6th Sense” symbol lights up. ADD WASHING/DOOR LOCK As soon as a programme starts, the “Door locked” symbol lights up on the display. You can interrupt the programme by pressing “Start (Pause)” - the light blinks. The “Door locked” symbol on the display goes off and you can open the door. In certain programme phases, the “Door locked” symbol remains lit to show that the door cannot be opened in the present programme phase, e. g. As long as the “Add garment” symbol lights up on the display, you can add more washing: press “Start (Pause)” , open the door, add your washing, close the door and press “Start (Pause)” to continue the programme. SAVE YOUR FAVOURITE PROGRAMMES If there is a programme setting which you use frequently, the washing machine offers the possibility to save one setting for each programme so that it can be used again by just pushing one button. • Select the desired programme, temperature, spin speed and options/modifiers. Press and hold the “Favourites” button for some seconds; the light goes on and a signal sounds when the programme setting is saved. Next time you want to use your individual programme setting, turn the programme selector to the desired programme, shortly push the and start by pressing “Start (Pause)” . “Favourites” button If you want to replace the saved setting by another one: • Select the programme desired and the new temperature, spin, options/modifier setting. • Press and hold the “Favourites” button for at least 3 seconds; the previously saved setting is replaced by the new one. The remaining programme time can also deviate from the values in the table as it depends on the size of your wash load, water inlet temperature etc. ; the remaining time indication is newly calculated and updated if necessary approximately 20 minutes after programme start. The consumption data for “Heavy duty” refer to a programme setting without “Eco” and “Heavy soil”, except the data which is indicated in the line marked with “***”. * To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. ** The grey shaded columns show energy consumptions and programme durations for the washing machine being connected to both hot and cold fill, with a hot fill inlet temperature of 60°C. The columns left from them show energy consumptions and programme durations for the washing machine being connected to cold water only by the Y-adapter. *** Reference programme for Energy Label (Heavy duty 60°C with default settings). ADD DETERGENT, CLOSE THE DOOR AND SELECT THE PROGRAMME Add the detergent as described in the programme table and in the chapter “Detergent and Additives” in your Instructions for Use. The light of the selected programme is on, and the “Start (Pause)” button blinks. Turn the programme selector to the desired programme it is marked by a light. The predefined temperature and spin speed can be altered by pressing the “Temperature” and the “Spin speed” modifier. SELECT ANY DESIRED OPTION OR MODIFIER Selecting any option or modifier, the indication lights up. If the combination of programme, options or modifiers is not possible, the indication lights switch off automatically and a signal sounds. “Eco” button • The duration of the wash is extended and the temperature reduced. [. . . ] b) Do not invert their position (for example: cold fill into hot inlet valve and viceversa). c) And see instruction for use “Connect the water supply hose”. Cold fill Hot fill Cold fill Y-adapter Connect cold water supply only (Fig. 2): You need a Y-adapter which you can obtain via our After-Sales Service or in the specialist trade. Connect the two inlet valves present on the rear of the machine to the Y-adapter using the relative provider hoses. [. . . ]