User manual X10 UR47A

[. . . ] It has been type tested and found to comply with the limits for remote control devices in accordance with the specifications in Sub-Parts B and C of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by unplugging the equipment, try to correct the interference by one or more of the following measures. · · · · Reorient the antenna of the radio/TV experiencing the interference. [. . . ] The Transceiver Module also passes on commands over your house wiring to control other X10 modules (also sold separately). Note that unlike the Lamp Module you cannot dim or brighten a lamp connected to the Transceiver Module. You should locate the Transceiver Module centrally in the home for maximum range when controlled by the SuperRemote. 1 . Plug the Lamp Module into a convenient AC outlet. SUPER X10 DVD S UPER R EMOTE The X10 DVD SuperRemote allows you to control practically everything electrical in your home. It has IR technology that lets you control all your TV, VCR, Cable Box, Satellite equipment, DVD Player; and X10 RF technology that lets you control lamps and appliances anywhere in your home. To find out more about configuring the SuperRemote to work with your audio/ video equipment, see the section titled "Setting Up your SuperRemote. " 1 . Fully extend the antenna. MODULE L AMP M ODULE The Lamp Module (sold separately) can be used to control any incandescent lamp rated up to 300W. It is not suitable for other types of lamp such as fluorescent or energy saving lamps, or lamps which include a dimmer control. Caution: Do not connect an appliance such as a coffee pot or heater to the Lamp Module. It may damage the module and the appliance and could cause a fire hazard. 8 2 . Fit four AAA batteries, taking care to match the + and - marks in the battery compartment. 9 SETTING UP S ETTING U P YOUR S UPERREMOTE DESCRIPTIONS B UTTON D ESCRIPTIONS Since this remote is primarily an X10 and DVD remote, the button description below refer to the operation when in DVD mode. If there are 2 or more titles on the DVD this button lets you to select another title. Toggles track/time/audio/subtitle/title information on and off the screen. Used as your original remote and to enter device codes for X10 Modules. Lets you control X10 modules to operate lamps and appliances around the home. A-B INDICATOR INDICATOR LIGHT ENT CHANNEL, VOLUME, MUTE POWER X10 ON/OFF KEYS TV, SAT TV, VCR, CBL, AUX, SAT, DVD TITLE S ETTING UP FOR TV, VCR, TV, C ABLE , S ATELLITE /DSS, AND SA DVD 1 . Turn on the device you want to control (TV VCR, cable , box, satellite receiver, DVD, etc. ). Release the SETUP button. SUBTITLE AY D I S P L AY RETURN UP/DOWN/LEFT/RIGHT DVD KEYS OK Menu Select/OK/Enter button. Last play/repeat. 10 MENU EXIT SKIP BACK SKIP FOR WARD 3 . Press and release the mode button that matches the device you want to control. The LED turns off after the last digit entered. 11 PLAY FF, STOP, PAUSE REW, PLAY, FF, REC, STOP, PAUSE RECALL 5 . Your device should turn off. U SING AUX TO CONTROL A TV, CABLE BOX OX, S ECOND TV, VCR, C ABLE B OX , RECEIVER S ATELLITE R ECEIVER , OR DVD The AUX button is normally used to control an audio component, but it can also be configured to control a second TV, VCR, cable box or satellite receiver. 6 . Turn on the equipment you want to control. Notes: For CD players use the AUX buttons. [. . . ] X10 agrees to repair or replace, at its sole discretion, a defective X10 product if returned to X10 within the warranty period and with proof of purchase. If service is required under this warranty: Call 1-800-442-5065, visit www. x10. com, or e-mail support@x10. com. The Transceiver Module works, but other Modules don't respond: · Check that the Module has the same House Code as the Transceiver Module. Try plugging the Module into a different outlet. For help or more information on setup, please visit: http://www. x10. com/support · Note: if you use an RF Transceiver (such as the RR501 or TM751) to control X10 Modules, you will be able to control up to 16 Modules. When using a Transceiver, when you press 1-6-ON you turn on Module number 16. [. . . ]