Detailed instructions for use are in the User's Guide.
[. . . ] This equipment generates and uses radio frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturers instructions, it may cause interference to radio and television reception. It has been type tested and found to comply with the limits for remote control devices in accordance with the specifications in Sub-Parts B and C of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by unplugging the equipment, try to correct the interference by one or more of the following measures. [. . . ] Push the tab and lift off the battery cover.
MODULE LAMP MODULE
The Lamp Module (sold separately) may be used to control any incandescent lamp rated up to 300W. It is not suitable for other types of lamp such as fluorescent or energy saving lamps, or lamps which include a dimmer control. Caution: Do not connect an appliance such as a coffee pot or heater to the Lamp Module. It may damage the module and the appliance and could cause a fire hazard.
8
2 . Fit four AAA batteries, taking care to match the + and marks in the battery compartment.
9
SETTING UP SETTING UP REMOTE YOUR REMOTE
DESCRIPTIONS BUTTON DESCRIPTIONS
INDICATOR INDICATOR LIGHT
OK
Select Menu items of the device you are controlling.
The indicator light flashes when the remote is operating. Lets you control X10 modules to operate lamps and appliances around the home. Access the Menu function of the device you are controlling (if available).
PLAY, REW, FF, STOP PAUSE , REC , PLAY REW, FF, STOP PAUSE, Work the same as on your original remote. You must press the REC button twice to begin recording.
LEARN
POWER
TV, CABLE ABLE, SETTING UP FOR TV, VCR, CABLE, AND SATELLITE
1 . Turn on the device you want to control (TV VCR, cable box, , satellite receiver etc. ).
TV, VCR, CBL, SAT TV, SAT X10
SET UP LAST
2 . Your device should turn off.
A-B
MENU
EXIT Used to exit Menu functions. NAVIGA VIGATION NAVIGATION ARROWS
Used to navigate and adjust Menu items of the device you are controlling.
10
6 . The TV mode key can only be used to store TV codes but you can store a code for ANY device under either the VCR, CBL, or SAT mode key. E. G. , you can store a Cable code under the VCR key, or a Satellite code under the Cable key, etc. If your TV/VCR/Cable Box does not respond, try the other codes for your brand. If it still doesn't respond, try the Code Search method on page 13. If the LED blinked rapidly when you entered the code, you may have entered an invalid code. If some buttons do not operate your equipment, try one of the other codes for your brand. When searching for a code (page 13) you might have to press CHANNEL+ many times (50+). If the device does not have a Channel Up function, use the PLAY button (VCR only) or the POWER button.
FOR CODES SEARCHING FOR CODES
1 . Press and release the button on the UR74A Remote that you want to teach. Hold the button until the LED on the UR74A Remote blinks off.
14
15
7 . When you've finished learning all the keys, press SETUP .
CONTROLLING CONTROLLING MODULES X10 MODULES
If you have purchased and installed a Transceiver Module, you can control it and other X10 modules as follows:
1 . [. . . ] If service is required under this warranty: Call 1-800-442-5065, visit www. x10. com, or e-mail support@x10. com.
The Transceiver Module works, but other modules don't respond: · Check that the Module has the same House Code as the Transceiver Module. Try plugging the Module into a different outlet.
For help or more information on setup, please visit: http://www. x10. com/support
·
Note: if you use an RF Transceiver (such as the RR501 or TM751) to control X10 Modules, you will be able to control up to 16 Modules. With a Transceiver, when you press 1-6-ON you turn on Module number 16. However, if you use an IR543, when you press 1-6-ON you turn on Modules 1 AND 6. [. . . ]