User manual YAESU FT-2400H-3 SERVICE MANUAL

[. . . ] SCOPE: The left edge signal is corrected when the frequency is changed on the display. Ver. 11. 54 EDSP implements improvements (also includes all previous updates): · Corrected FM TX for a slight frequency offset. NOTES: *Rotate the [METER] switch to select "COM" (Compression). *When menu settings are saved on the DMU-2000 CF card and transferred to the new version, some previous versions may not transfer correctly. Please check your menu, update the settings, and then save the new settings to the CF card. Install the data file to PC 1. [. . . ] Save the FT-2000 data file [FT-2000_PEP2000_4-23-10. zip] to the desktop on your computer. Unzip and Extract the contents of [FT-2000_PEP2000_4-23-10. zip] to the desktop of your computer. You will find the PEP2000_EDSP3 and PEP2000_MAIN folders on your desktop. The programmers and software are now stored on your computer on the desktop. The files designated in the last step above are ready to update your FT-2000/D Transceiver. MAIN Software Update This procedure is used for uploading new Software into the FT-2000/D Amateur Transceivers using the CT-119 program cable. If you have the 8pin mini-DIN PGM-SW (P0091526) refer to the 8-pin mini-DIN PGM-SW page 4. *Don't forget to write down (or save to a CF Card) any personal menu settings you have changed from the default before you start. Please see the DMU-2000 Data Management Operation Manual for the procedure to save your settings to a CF card. (1) Turn off the main power switch located on the back of the FT-2000 (or turn off the power supply for FT-2400H-3 and wait a minute, until the capacitors discharge) and remove the AC power cord. (2) (3) Connect the CT-119 Cable's DB9F connector to the serial port COM1 in the back of your computer. If you use a USB to serial adapter, you might need to change the COM Port number. Now go to the desktop open PEP2000_MAIN folder and find the FSW003 icon as shown below. Double-click the FSW003 icon, displayed on the Program Screen. NOTE: If you receive a "communications error" message on your screen, click on the Configure box and choose a different COM port from the drop down menu. Then click the WRITE button again. (4) (5) When the program opens, confirm that the file AH025_V0151. SFL is highlighted; if not, click on it to highlight it. NOTE: We recommend trying the new factory default settings rather than transferring your old ones, because of the changes in the EDSP and the Main CPU, you may wish to make new settings. We hope this new software will increase your enjoyment of your FT-2000/D. If you have any problems or questions please contact Vertex Standard, Amateur Tech Support. amateurtech@vxstdusa. com Best regards, Mikio Maruya, WA6F Executive Vice President Engineering & Customer Service Vertex Standard USA, Inc. Vertex Standard USA, Inc. | Cypress, CA 90630 | 714. 827-7600 | FAX: 714. 827-8100 www. vertexstandard. com ADDENDUM If the CT-119 programming cable or 8-pin mini-DIN PGM-SW (P0091526) is not available you will need a serial cable RS-232C, DB9F to DB9F straight cable. MAIN Software Update *Don't forget to write down (or save to a CF Card) any personal menu settings you have changed from the default before you start. Please see the DMU-2000 Data Management Operation Manual for the procedure to save your settings to a CF card. We recommend you follow this process, steps (1) thru (18), the first time you program your radio. After you are familiar with the location of the switch S3004 you may wish to bypass Steps (2) and (15), and operate the switch through the hole under the left rear foot (near the CAT connector). You must be extremely careful to avoid damage to the PC components (which may not be covered by the Limited Warranty). (1) Turn off the main power switch located on the back of the FT-2000 (or turn off the power supply for FT-2400H-3 and wait a minute, until the capacitors discharge) and remove the AC power cord. To find and operate the switch, remove the top cover (9 black screws). Carefully Place the Transceiver bottom side up on a sturdy cleared worktable. [. . . ] Find the micro-switch on the pc board near the rear right hand corner when looking down at the bottom of the FT-2000/D. (See the attached photo. ) (2) (3) (4) (5) (6) Connect a serial cable RS-232C, DB9F to DB9F straight cable to the COM1 connector of your computer and the 9-pin CAT connector on the rear of the transceiver. If you use a USB to serial adapter, you might need to change the COM Port number. (In the case of the FT-2400H-3 connect the power supply cables. ) Turn on the main power switch. [. . . ]