User manual YAESU FT-7100M

[. . . ] OPERATING MANUAL VERTEX STANDARD CO. , LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 17210 Edwards Rd. , Cerritos, CA 90703, U. S. A. 52nd Terrace, Suite 201, Miami, FL 33166, U. S. A. YAESU EUROPE B. V. P. O. Box 75525, 1118 ZN Schiphol, The Netherlands YAESU UK LTD. Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U. K. YAESU GERMANY GmbH Am Kronberger Hang 2, D-65824 Schwalbach, Germany VERTEX STANDARD HK LTD. 11th Floor Tsim Sha Tsui Centre, 66 Mody Rd. , Tsim Sha Tsui East, Kowloon, Hong Kong Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Rotate the Main Dial knob to select the DTMF Autodialer memory channel number into which you wish store a telephone number ("CH-01" ~ "CH-16"). Use the Main Dial knob (or the microphone's [UP]/ [DWN] buttons) to select the first digits of the telephone DTMF Autodialer Memory number you wish to store. When you have selected the correct digit, press the [LOW] Current Digit key momentarily. Now, use the Main Dial knob (or the microphone's [UP]/ [DWN] buttons) to select the second of 16 available digits in the current DTMF Autodialer memory. If you mistake an error during programming, you may press the [REV] key momentarily as a backspace key. If you wish to erase all digits before the current one, press and hold in the [REV] key for 1/2 second. You may now press the [TONE] key momentarily to review your entry for accuracy. Use the Main Dial knob (or the microphone's [UP]/[DWN] buttons) to select another DTMF Autodialer memory channel, and repeat the process described above, beginning in step 4. When you are done programming all desired DTMF Autodialer memory channels, press and hold in the [BAND] key for 1/2 second to exit to normal operation. 28 FT-7100M Operating Manual OPERATION TRANSMISSION To transmit the memorized telephone number, used the following procedure: 1. While holding in the PTT switch, rotate the Main Dial knob to select the DTMF Autodialer memory channel you wish to send, then press the [HOME] key. One the string begins, you may release the PTT switch, as the transmitter will be held "on the air" until the DTMF string is completed. Three speed levels are available: 50 ms (20 digits per second, the default setting), 75 ms (13 digits per second), and 100 ms (10 digits per second). Press and hold in the [BAND] key for 1/2 second to activate the "Menu" mode. Press the [BAND] key momentarily to enable changing of this Menu item. Rotate the Main Dial knob to select the desired speed ("50ms, " "75ms, " or "100ms"). Press and hold the [BAND] key for 1/2 second to save the new setting and exit normal operation. You can also set a longer delay between the time the [HOME] key is pressed and the first DTMF digit is send. To set the delay time, use the following procedure: Press and hold the [BAND] key for 1/2 second to activate the "Menu" mode. Press the [BAND] key momentarily to enable changing of this Menu item. Rotate the Main Dial knob to select the desired speed from the available choices ("50ms, " "250ms, " "450ms, " "750ms, " or "1000ms"). Press and hold in the [BAND] key for 1/2 second to save the new setting and exit normal operation. Important Note Do not attempt to utilize the DTMF features, either manually or Auto-dialing, while you are driving. Always park you car before dialing, in the interest of safety to you, your passengers, and other drivers. FT-7100M Operating Manual 29 OPERATION TRANSMISSION Transmitter Time-Out Timer (TOT) The "Time-Out Timer" (TOT) feature is designed to force the transceiver into the "receive" mode after a preset time period of continuous transmission (the default is 6 minutes). [. . . ] Available Values: SQL OFF, TCALL, RPTR, PRI, LOW, TONE, MHz, REV, HOME, BAND, VFO/MR Default Setting: LOW Note: [P4] button for MH-48A6J, [P2] button for MH-42B6SJ Menu Item 24 [RFSQL] Function: Adjusts the RF SQL threshold level. Available Values: S-1/S-5/S-9/S-FULL/OFF Default Setting: OFF Note: This Menu item can be set independently for each band. Available Values: BUSY/TIME Default Setting: BUSY Note: This Menu item can be set independently for each band. Menu Item 26 [SHIFT] Function: Sets the magnitude of the Repeater Shift. [. . . ]