User manual ZALMAN 9700

[. . . ] 3) Innovative and patented, curved heatpipe design for a heat transfer capacity of up to six heatpipes with the use of just three. 4) 0. 2mm ultra-slim fins for minimized weight and reduced airflow resistance. Model CNPS9700 LED Note (1) The maximum weight for a cooler is specified as 450g for Intel Socket 775 and AMD Sockets 754/939/940. Special care should be taken when moving a computer equipped with a cooler that exceeds the specified weight limit. [. . . ] Refer to the following diagrams, and install only on systems that meet the following installation requirements : No interfering components (PSU, graphic card etc. ) within 62mm from the center of the CPU. No interfering components (ODD etc. ) within 48mm from the center of the CPU. Case cover must be at least 150mm apart from the motherboard. Case Cover PSU 62mm System Fan Air Flow 62mm Case 48mm Graphic Card Slot Motherboard 9. Installation The Clip Installation Method The CNPS9700 must be installed in the orientation that matches the rear system fan's airflow. (Refer to the diagram above) The Clip installation method depends on the motherboard's socket orientation. Be careful not to exert excessive force on the fan during installation of the Clip, as it may damage the fan. A. For motherboards with a horizontally-oriented Retention Guide Clip Retention Guide B. For motherboards with a vertically-oriented Retention Guide Clip Retention Guide 150mm 3 1) Intel Socket 775 Clip Installation Refer to "The Clip Installation Method" on page 3 to correctly install the Clip (S-Type, the orientation of the Retention Guide. ) according to Clip Support Installation Align the Clip Support for Socket 775 ( ) and the Backplate for Socket 775 ( ) with the mounting holes on the motherboard, and fasten them together by using the Clip Support Fixing Bolts ( ). The Lever Slot on the Clip Support for Socket 775 ( ) must be properly oriented on the hinged side of the socket lever when installing. The Backplate Support on the Backplate for Socket 775 ( ) can be removed if deemed unnecessary. Clip Support Fixing Bolt, CPU Clip Support for Socket 775, Socket Lever Hinge Motherboard Backplate for Socket 775, Backplate Support CPU Socket Lever Lever Slot Thermal Grease Application Clear off particles or any residue from the contact surface of the CPU and heatsink. Shake the Thermal Grease (ZM-STG1, ) well then apply on the contact surface of the CPU and heatsink base. Cooler Installation Insert two Bolts ( ) into the holes of the Clip (S-type, ) and place the CNPS9700 on the center of the CPU. Slightly fasten the Bolts ( ) into the holes of the Clip Support for Socket 775 ( ), then fasten the Bolts ( ) in an alternating manner until the Clip (S-Type, ) is completely pressed against the Clip Support for Socket 775. Bolt, Clip(S-Type), Note When installing the CNPS9700 on a motherboard with a horizontallyoriented Retention Guide, take extra care to not exert excessive force on the fan. Excessive force may damage the fan. Power Connection (FAN MATE 2) Please refer to "FAN-MATE 2 Installation and Usage" on page 6. 4 2) AMD Socket AM2/754/939/940 Thermal Grease Application Clear off particles or any residue from the contact surface of the CPU and heatsink. Shake the Thermal Grease (ZM-STG1, ) well then apply on the contact surface of the CPU and heatsink base. Clip Installation Refer to "The Clip Installation Method" on page 3 to correctly install the Clip for AMD Sockets ( ) and Clip Lever ( ) on the CNPS9700 according to the orientation of the Retention Frame. First insert the Clip for AMD Sockets ( ) into the Heatsink ( ), then connect the Clip Lever ( ) with the Clip ( ). Align and connect the Slot of the Clip ( ) with the Center Lug of the Retention Frame. Press onto the Clip Lever ( ) when aligning the Clip Slot and Center Lug. Clip's Slot Clip Lever, Lever's Slot Center Lug Center Lug Power Connection (FAN MATE 2) Please refer to "FAN-MATE 2 Installation and Usage" on page 6. 5 10. FAN MATE 2 Installation and Usage 1) FAN MATE 2 Installation Inside a System 2) FAN MATE 2 Installation on the Outside of a System Double - sided Tape Fan Connector (CNPS9700) FAN MATE 2 6-Pin Connector Motherboard Connect the two 3-pin connectors of the cable to the motherboard and to the CNPS9700's Fan Connector as shown in the diagram. Pull the 6-Pin Connector out of the system through the back and connect it to FAN MATE2, which should be installed on the case using the included Double-sided Tape ( ). The fan operates in Silent Mode when the speed control knob of FAN MATE 2 is fully turned in the counter-clockwise direction. The fan operates in Normal Mode when the speed control knob of FAN MATE 2 is fully turned in the clock-wise direction. [. . . ] is not responsible for any damages resulting from CPU Overclocking. 6 12. Zalman Computer Noise Prevention System Zalman's Noiseless Power Supplies, Fanless Northbridge Coolers, Heatpipe HDD Cooler, Noiseless Case Fans, VGA Coolers, and Fan Controllers facilitate stable performance and a noiseless computing environment. 13. TNN (Totally No Noise) Computer Enclosures TNN 300 TNN 500AF TNN Computer Enclosures are the world's first environment-friendly noiseless computer enclosures that operate without the use of a fan. TNN Computer Enclosures use the aluminum enclosure itself as a heatsink. [. . . ]