User manual ZALMAN ZM550-XG 80PLUS GOLD

[. . . ] 3) Three types of compression fitting are offered for use with water tubes (8X10mm, 8X11mm, 10X13mm) * Zalman Tech. is not responsible for any damage resulting from CPU OVERCLOCKING. 2. [. . . ] Specifications Part No 1 2 3 4 5 6 7 8 9 10 11 12 13 Part name CPU block Hand screw Thermal grease Clip User's manual Clip supports Clip supports A Clip supports B Bolts Paper washer Nipple Back plate Fitting 3 set Q' ty 1 2 1 1 1 2 2 2 4 1 set 2 6. 2 60. 0 8. 2 5. 0 5. 0 0. 8 Socket 478 Socket 462 Socket 462 Clip supports, A, B-type 7, 8 mountimg Socket 754 mountimg Socket 754 mountimg Fitting to 8 x 10mm, 8 x 11mm, 10 x 13mm tubes Weight (g) 447. 0 8. 0 1. 8 9. 6 Use CPU mountimg Clip mountimg Apply to cpu core CPU block mountimg NOTE 1) The maximum weight for the cooler is specified as 450g/450g/300g for socket 478/754/462 respectively. Special care should be taken when moving a computer equipped with a cooler which exceeds the relevant weight limit. Zalman Tech Is not responsible for any damage that occurs when moving a computer. 1 3. Exploded View 1) Exploded view of CPU block a Block base Fittings a 2) Exploded view for CPU type using ZM-WB2 Gold Intel Pentium 4 Socket 478 CPU AMD Athlon 64 Socket 754 CPU AMD Athlon/ Duron/Athlon XP Socket 462 CPU 2 4. (3 sets) 2) Components for Intel Pentium 4 (Socket 478) Two (2) Clip Supports for Socket 478 3) Components for AMD Athlon / Athlon XP (Socket 462) One (1) A -Type(blue) Clip Support for AMD Socket 462 One (1) B -Type(white) Clip Support for AMD Socket 462 Four Bolts - For Fastening Clip Supports One Set of Washers 4) Components for AMD Athlon 64 (Socket 754) Two Nipples One Backplate 3 5. Compatible CPU Types 1) Intel Pentium 4 - Socket 478 All speeds of Pentium 4 Socket 478 CPUs Caution As shown in Figure 2, a mainboard that is not compliant with the "10. 2 mm mainboard component height restriction" standard, introduced by Intel, may create interference between components and the clip. Installation-AMD XP/Duron, Socket 462 1) Install Clip spport Install the socket 462 clip supports as shown on the right. Be sure to install A -Type clip Paper support (Blue) next to the lever. washer Mainboard B-Type Clip Support (White) A-Type Clip Support (Blue) Lever Paper washer Bolts B-Type Clip Support (White) 6 2) Apply Thermal Grease Spread thermal grease thinly and evenly over the CPU. CPU 3) Insert Hand screws Insert hand screws into the outer holes on the clip. Thermal Grease 4) Fasten Hand screws Place the CPU block on the center of the CPU. Screw in both hand screws in an alternating fashion until they are completely tightened. Outer hole Clip A-Type Clip Support B-Type Clip Support Inner hole 9. Installation-AMD XP/Duron, Socket 462 1) Fasten Nipples Position the backplate on the bottom of the mainboard under the CPU socket, then fasten the nipples as shown on the right. * When installing the ZM-WB2 on an Athlon 64, the retention frame is not needed. Nipple Large Hole Washer Main board Backplate 7 2) Apply Thermal Grease Spread thermal grease thinly and evenly over the CPU. CPU 3) Insert Hand screws Insert hand screws into the outer holes on the clip. Thermal Grease 4) Fasten Hand screws Place the CPU block on the center of the CPU. [. . . ] Installation-AMD XP/Duron, Socket 462 1) Fasten Nipples Position the backplate on the bottom of the mainboard under the CPU socket, then fasten the nipples as shown on the right. * When installing the ZM-WB2 on an Athlon 64, the retention frame is not needed. Nipple Large Hole Washer Main board Backplate 7 2) Apply Thermal Grease Spread thermal grease thinly and evenly over the CPU. CPU 3) Insert Hand screws Insert hand screws into the outer holes on the clip. Thermal Grease 4) Fasten Hand screws Place the CPU block on the center of the CPU. [. . . ]