User manual ZEKTOR HDVI5
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ZEKTOR HDVI5. We hope that this ZEKTOR HDVI5 user guide will be useful to you.
You may also download the following manuals related to this product:
ZEKTOR HDVI5 SUPPLEMENT (495 ko)
Manual abstract: user guide ZEKTOR HDVI5
Detailed instructions for use are in the User's Guide.
[. . . ] ZEKTOR
Ho m e T h e a t e r Switches
Digital Video / Component Video / Multichannel Audio
HDVI5
1 2 3 4 5 SEL A1 A2
Digital Video Switch
Rev 3 08/08/2006
Contents
What's Inside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
What's Inside
Thank you for your purchase of the HDVI5 H igh D efinition Component Video Switch. Ever y care has been taken to assure you of a successful installation and subsequent operation of your new HDVI5 video switch, however should something go wrong, and war rant y repair wor k is needed, we request that you hold on to the or iginal pack aging mater ials. 4.
HDVI5 R emote Control (ZRM) Power Supply M odule This User 's M anual
I f anything is missing please get in touch with us as soon as possible so that we can cor rec t the situation.
ii
HDVI5 Component Video Switch
HDVI5 Component Video Switch
An Overview of the HDVI5
Front Panel
1 2 3
Front Panel Controls:
1. [. . . ] The 'A' and 'A2' buttons are used to set the delay times 'A' decreases the delay time. The new settings are saved in non-volatile memor y and are not affec ted by a power failure.
HDVI5 Component Video Switch 23
Step 2: Enter the Switching Delay Setup Mode
After pressing '5', the standby LED continues to flash, and the front panel will display the current delay settings.
Step 3: Adjust Switching Delay Times
1 2 3 4 5 SEL A1 A2
Toggle between audio and video delays Decrease delay Increase delay Exit setup mode
22 HDVI5 Component Video Switch
Step 3: Adjust Switching Delay Times
· ·
Note:
Step 1: Place the HDVI5 into the Cable Length Tuning Mode
Input Cable Length Tuning
A2
1
2
3
4
5
SEL
A1
The HDVI5 features receiver equalization that can be used to compensate for the losses that occur in var ying length, and var ying qualit y, cables. Using high qualit y DVI or DVI to HDMI conversion cables, the HDVI5 can compensate for cables of up to 65 feet (20 meters), on all its inputs and still reliably receive a stable, spar k le free image at 080p. To tune an HDVI5's input to a specific cable length. . .
Press and hold the desired channel until the HDVI5 enters the cable length tuning mode. This example demonstrates entering the cable length setup mode for input '5'.
Step 1: Place the HDVI5 into the Cable Length Adj. Mode
· · · · · ·
Press the desired input and hold the button for seconds, until the HDVI5 enters the Cable Length Adj. Use the 'A' and 'A2' buttons to tune cable length. Use the Power Toggle button to exit the setup mode.
Step 2: Enter the Cable Length Adj. Mode
Step 2: Adjust cable length settings
1
2
3
4
5
SEL
A1
A2
Toggle between cable length and bandwidth settings. (Blue = Length, Red = Bandwidth) Decrease Cable Length Increase Cable Length Exit Setup Mode
When a cable's tuning is too shor t, the display will begin to spar k le, eventually going blank . For best results, star t long, and use a length a step or t wo above any noticeable ar tifac ts on the screen. Tuning a shor t cable too long increases its susceptibilit y to noise, causing possible drop outs and spar k les. Note: O utput c able lengths depend on the display's receiver's c apabilities, and the qualit y of c abling used. The HDVI5 uses source termination to compensate for all lengths of output c ables, and to help in c ases where the receiver may not have followed the specific ations properly. Each input c an be tuned individually and all settings are saved in non-volatile memor y and are not affec ted by a power failure.
HDVI5 Component Video Switch 25
Note:
2 HDVI5 Component Video Switch
Step 1: Place the HDVI5 into the Cable Length Tuning Mode
Bandwidth & Sync Settings
A2
1
2
3
4
5
SEL
A1
Press and hold the desired channel until the HDVI5 enters the cable length tuning mode.
The HDVI5 is a fully digital switch, unlike many similar produc ts, the HDVI5 decodes the DVI/HDMI signal and re - encodes it on the output. This allows it to cor rec t for many non- compliant devices attached to its inputs, and always generate fully compliant HDMI/DVI data on its output. The following parameters are usually best lef t alone and will have no affec t on a fully compliant DVI/HDMI source, but may be useful when connec ting to a non- compliant source. Bandwidth: This setting allows the HDVI5 to sync to sources with clocks that are unstable and are outside the DVI/HDMI specifications. The larger the bandwidth, the better the HDVI5 can to lock on to non-standard sources at the expense of being more susceptible to noise. S ome PC cards, and older DVD players, may require this value to be set high (6MH z) to wor k reliably.
Step 2: Adjust Bandwidth and Sync Settings
HSJitter: S ome non- compliant sources can generate hor izontal jitter, causing the screen to jump back and for th hor izontally. Enabling this setting (blue LED is lit) will eliminate this problem on all resolutions where the hor izontal pixel size is evenly divisible by four.
5 SEL A1 A2
1
2
3
4
HSyncandVSync: When set to their default values, these settings have no effec t on the HSync a VSync signals. I f a source and monitor will not wor k with each other, using the HDVI5 and enabling one or both of these settings (blue LEDs are lit) may fix the incompatibilit y.
Toggle between Length & Bandwidth Settings. [. . . ] (Note: The HDVI5 does not break out the HDMI audio from the HDMI video. ) Adjustable front panel LED intensities. Eliminate the distraction of glaring LEDs by having the front panel dim after a few seconds of sitting idle. Two dry contact (low voltage) relays are avail able to control whatever might need controlling. Each relay can be controlled using IR, RS-232, or front panel buttons. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ZEKTOR HDVI5
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ZEKTOR HDVI5 will begin.