User manual ZENITH H20H52DT

[. . . ] Installation and Operating Guide Warranty Model Number H20H52DT HW20H52DT zenith ® Please read this manual carefully before operating your set. See the label attached on the back cover and quote this information to your dealer when you require service. table of contents page 5 Internet Home Page : http://www. zenith. com P/N : 3828VA0518B a (FCH-50) For Customer Support/Service please call: 1-888-865-3026 www. zenith. com WARNING RISK OF ELECTRIC SHOCK RECORD THE MODEL NUMBER The serial number of this HealthViewTM TV is located on the back of the cabinet. For future reference, we suggest that you record the serial number here: MODEL NO. H20H52DT/HW20H52DT SERIAL NO. _________________________ WA R N I N G : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). [. . . ] Remember, you can "blank" a channel for accommodating audio-only, such as an FM radio station or in-house communication. You may leave any unused bank with the channels entered during Auto Program; or, you may delete the channels. However, you may want to leave at least one channel in any unused bank. Then, if someone selects an "unused" bank, that channel will assure them that the TV is functional. Note: Some channels from factory testing may be in the channel banks if you have not yet run Auto Program. Program package Basic cable channels Extended cable channels Extended with premium channels 4 Other cable installer options (Grouping is provided as an example only. ) Channel Bank 1 2 3 Note: Be advised that running Auto Program overwrites any custom channel setups; removes Blanked, Deleted. Select a channel bank with an installer remote -press SOURCE/BANK (and repeat). CHANNEL BANK and BANK number will be displayed. CHANNEL BANK BANK 1 Channel bank number display 3. Use the ADD/DEL/BLNK item (also in the Setup menu) to customize your program package. You can also "Blank" a channel for accommodating an audio-only program source or in-house communication. Inactive TV Display (Channel Bank 4) The TV can be set up to be inactive; which would require an attendant using an installer remote to change to a "billable" active channel bank selection: Bank 1, 2, or 3. Note: For institution control of patient-accessible programming, channels in Bank 4 need to be removed. The BLNK (blank) channel function is "global" -- the same channel number is blanked in channel banks 1, 2, 3, and 4. ADDING / DELETING CHANNELS A previously prepared programming chart is helpful. All channels found on your cable/antenna will be entered in Channel Banks 1, 2, 3, and 4. INACTIVE TV PLEASE . CALL A TTENDANT Page 28 Managing the Channel Banks Examples of typical channel banks chart. Figure 1. Typical channel banks after running Auto Program B A Purpose N K Channel Number 1 2 3 4 5 67 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A= Active - - Channel was found during AUTO PROGRAM. Typical channel banks after running Auto Program, and customizing with Add/Dell/Blnk B A Purpose N K Channel Number 1 2 3 4 5 67 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 Basic Extend All CTV Other BC BC BC BC A A A A A A A A A A A A A A A A A A A A D A A A D D D A D A A A D A A A D D D A D A A A D A A A D A A A D D A A D D D A D D A A D D A A A = Active D = Deleted BC = Blanked Channel Channel was found during AUTO PROGRAM Channel was deleted using Add/ Del option. Channel was blanked using BLANK channel option (ADD/DEL/BLNK). ADDING / DELETING CHANNELS It is best to do ADD / DEL customizing before doing "BLNK. " AUTO PROGRAM enters the same channels in Banks 1, 2, 3, and 4. AUTO PROGRAM removes any channels previously customized with ADD / DEL / BLNK. The channels available on your antenna / cable will be entered, and any channels previously entered but not currently available will be deleted. ADD and DEL (not BLNK) can be used independently for channel banks 1, 2, 3, and 4. Channel allocations in tuning bands: BROADCAST: 2 ­ 69 CABLE ­ CATV, HRC or ICC: 1 ­ 125 Page 29 Managing the Channel Banks PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies) B A N K Channel Number Purpose 1 2 3 4 5 67 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 B A N K Purpose 26 27 28 29 30 31 32 33 34 35 Channel Number 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 2 3 4 B A N K Purpose 51 52 53 54 55 56 57 58 59 60 Channel Number 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 1 2 3 4 B A N K Purpose 76 77 78 79 80 81 82 83 84 85 Channel Number 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 1 2 3 4 B A N K Purpose Channel Number 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 FM 1 2 3 4 Page 30 Installer Menus Use the Installer's Menus to make TV operation adjustments. Accessing the Installer's Menu Installer's menus can be accessed by using the optional installer's remote control. Just press and hold MENU (about 8 seconds) until the display changes, then press 9, 8, 7, 6, then ENTER. [. . . ] jack is used for cloning TV's features. ) Refers to the jack that sends a signal out of a VCR, DVD, or other A/V device. Picture and sound traveling through a cable, or over the air, to the television screen. Device that picks up the audio/video signal and turns it into picture and sound. Extended Data Service: Additional program information if provided by the broadcaster. 300 TO 75 OHM ADAPTER A/V DEVICE ADD AMPLIFIER ANTENNA AUTO PROGRAM DELETE INPUT JACK MONO SOUND M. P. I. OUTPUT SIGNAL TUNER XDS Page 51 WARRANTY Direct-View Welcome to the Zenith family! [. . . ]