User manual ZENITH H2534Y33 OPERATING GUIDE

[. . . ] machine numbers H 1934DT H2034DT H 2 5 3 4 DT H2539Y ConciergeTM Direct View Television Receiver installation & operating guide / warranty WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. POWER CORD POLARIZATION: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. [. . . ] Typical channel banks after running Auto Program B Purpose A N K 1 2 3 4 Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A = Active - - Channel was found during AUTO PROGRAM Figure 2. Typical channel banks after running Auto Program, and customizing with Add/Del/Blnk B Purpose A N K 1 2 3 4 Basic Extend All CTV Other Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 BC A BC A BC A BC A A A A A A A A A A A A A A A A A D A A A D D D A D A A A D A A A D D D A D A A A D A A A D A A A D D A A D D D A D D A A D D A A A = Active D = Deleted BC = Blanked Channel Channel was found during AUTO PROGRAM Channel was deleted using Add/ Del option. Channel was blanked using BLANK channel option (ADD/DEL/BLNK). ADDING / DELETING CHANNELS It is best to do ADD / DEL customizing before doing "BLNK. " AUTO PROGRAM enters the same channels in banks 1, 2, 3, and 4. AUTO PROGRAM removes any channels previously customized with ADD / DEL / BLNK. The channels available on your antenna / cable will be entered, and any channels previously entered but not currently available will be deleted. ADD and DEL (not BLNK) can be used independently for channel banks 1, 2, 3, and 4. Channel allocations in tuning bands: BROADCAST: 2 ­ 69 CABLE ­ CATV, HRC or ICC: 1 ­ 125 206-3490-O PAGE 27 Managing the Channel Banks PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies). B Purpose A N K 1 2 3 4 Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 B Purpose A N K 1 2 3 4 Channel Number 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 B Purpose A N K 1 2 3 4 Channel Number 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 B Purpose A N K 1 2 3 4 Channel Number 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 B Purpose Channel Number A 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 FM N K 1 2 3 4 PAGE 28 206-3490-O Installer's Menus Use the Installer's Menus to make adjustments. Accessing the Installer's Menu Installer's menus can be accessed by using the installer's remote control. Just press and hold MENU (about 8 seconds) until the display changes, then press 9, 8, 7, 6, then ENTER. Or, access an item directly by entering the line number, then pressing MENU. For example, to access the Start channel/volume feature which is on line 11, press 11, then MENU. To change a current setting use the Left/Right ADJ keys. 1390-00 0. 00 01 03 VERT POS 13 Using the Installer's Menu Items 00-22 are immediately accessible only upon entering the Installer's Menu. Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below. A second section of the Installer's Menu that is intended for qualified service technicians only is not shown (items 23-49). Normally these items do not require adjustment. XX/XX/9X TE = 11111111 Items in the Installer's Menu: Item 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 21 22 22 206-3490-O Description FACT MENU PRESET PX POWER MANAGE VERT POS HORZ POS BAND/AFC MIN VOLUME MAX VOLUME AC ON KEY DEFEAT STRT CH/VOL HOSPITAL MODE CHAN LOCK GHOST CH. OVERRIDE OLD OCV CAPTION LOCK FUNCTION PRE FEATURE LEVEL Range 0-2 0-1 0-7 0 - 25 1 - 15 0-7 0 - 63 0 - 63 0-1 0-1 0 - 255 0-1 0-1 0-1 0-1 0-1 0-1 0-1 0-1 0-1 0-1 0-1 0-1 Fact. Set 0 1 0 15 29 0 0 63 0 0 255 0 0 0 0 1 1 1 1 0 0 0 1 Installer should leave item 00 FACT MODE set to 0 (default). Items 23-49 are service-type adjustments and only qualified technicians having specialized test equipment should access them. Recommend. Setting Leave default set 0 Leave default set 0 Leave default set 0 PAGE 29 Installer Menus Use the Installer's Menus to make adjustments. 00 FACT MENU (Factory Mode) Used to access and customize Installer's Menu settings using the installer type remotes. 01 PRESET PX (Preset Picture) Saves your custom video settings (color, tint, contrast, and brightness) in nonvolatile memory (not affected by power loss). Memory status is indicated by a 0 for "custom settings already stored, " or 1 for "custom settings have not been stored. " Make all custom video settings before you access the Installer's Menu and PRESET PX. When you use the ADJUST keys to toggle from 1 - 0, any changes in the video settings will be stored sure they are correct!These settings become the PRESET values for the PICTURE PREF option of the Video Menu. (For more information refer to the Video Menu section of this manual. ) 02 POWER MANAGE (Power Management) The POWER MANAGE function is for saving energy. [. . . ] Such replacement parts are warranted for the remaining portion of the original warranty period. Warranty service for 21" diagonal (U. S. A. ) or larger screen size models is provided in the home in most cases. (Some repairs may require the unit to be taken by the servicer to the repair facility and returned, at no additional charge. ) This warranty covers manufacturing defects and does not cover installation, adjustment of customer controls, installation or repair of antenna systems, cable converters or cable company-supplied equipment; it also does not cover damage due to misuse, abuse, negligence, acts of God or other causes beyond the control of Zenith. Any alteration of the product after manufacture voids this warranty in its entirety. [. . . ]