User manual ZENITH P42W24B OPERATING GUIDE

[. . . ] Installation and Operating Guide Model Numbers | P42W24B | PLASMA DISPLAY PANEL © Copyright 2002, Zenith Electronics Corporation. WARNING WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. FCC NOTICE · A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] · Sound options FLAT, SPORTS, CINEMA and MUSIC are preset for good sound quality at the factory and cannot be changed. Manual Sound Control (User option) - You can adjust sound treble, bass, and balance to the levels you prefer. 1. Press the G D /E F /G /E button to select the SOUND menu. SOUND DASP AVL TREBLE BASS BALANCE button to select the desired sound option. button to make appropriate adjustments. G 50 button and then use 4. Press the MENU button. AVL (Auto Volume Leveler) Volume - AVL maintains an equal volume level; even if you change channels. Press the G G D /E button to select the SOUND menu. SOUND DASP AVL TREBLE BASS BALANCE button and then use button and then use D /E D /E button to select A VL. Press the MENU button. 15 Special Menu Options Orbiter - Avoid allowing a fixed image to remain on the Monitor's screen for a long period of time. A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost image remaining even when you change the image. - To avoid a permanent image on the screen, the screen will move every 2 minutes: Left Downside Right Upside Upside Right Downside Left - The Orbiter feature may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. Press the G D /E button to select the SPECIAL menu. SPECIAL LANGUAGE KEY LOCK ORBITER WHITE WASH COLOR TEMP. Press the MENU button. D /E G ON OFF White Wash Wash - White Wash removes permanent images from the screen. - Note: An excessive permanent image may be impossible to clear entirely with White Wash. Press the G D /E button to select the SPECIAL menu. SPECIAL LANGUAGE KEY LOCK ORBITER WHITE WASH COLOR TEMP. SET ID button and then use D /E button to select WHITE WASH. 3. Press the MENU button. G ON OFF Key Lock - The monitor can be set up so that it can only be operated with the remote control. · Each press of the KEY LOCK button changes the screen display as shown below. ON OFF · You can also select ON or OFF in the SPECIAL menu. - This Monitor is programmed to remember which option it was last set to even if you turn the monitor off. - In KEY LOCK `ON', if the monitor is turned off with the remote control, press the INPUT SELECT button on the monitor or POWER, or INPUT SELECT on the remote control. - With the KEY LOCK ON, the display ` KEY LOCK' appears on the screen if any button on the front panel is pressed. 16 Adjusting Auto Color Control - To initialize values (reset to default settings), select the NORMAL option. - When adjusting color temperature options (red, green, or blue) manually, ACC automatically changes to USER. Press the G G G D /E button to select the SPECIAL menu. SPECIAL LANGUAGE KEY LOCK ORBITER WHITE WASH COLOR TEMP. SET ID button and then use D /E /E /E button to select COLOR TEMP . [. . . ] Acknowledgement [v][ ][Set ID][ ][OK][Data][x] Acknowledgement [y][ ][Set ID][ ][OK][Data][x] 25. Transmission [k][z][ ][Set ID][ ][FF][Cr] Data 0: Normal (Power on and signal) 1: No signal (Power on) 2: Turn the monitor off by remote control 3: Turn the monitor off by sleep time function 4: Turn the monitor off by RS-232C function 5: 5V down 6: AC down Acknowledgement [z][ ][Set ID][ ][OK][Data][x] * This function is "read only". 22. Green Adjustment (Command2:w) G To adjust green in color temperature. Transmission [k][w][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 64 * Refer to `Real data mapping 2' as shown below. [. . . ]