User manual ZIBRO R610C

[. . . ] Please read these Directions for Use first, to ensure the maximum lifetime for your Zibro heater. This appliance comes with a 48-month manufacturer's warranty on all defects in material or workmanship. We wish you much warmth and comfort from your Zibro heater. Yours sincerely, PVG International b. v. Customer Service Department 1 READ THE DIRECTIONS FOR USE FIRST. 2 IN CASE OF ANY DOUBT, CONTACT YOUR DEALER. 3 BEFORE YOU START READING, FOLD OUT THE LAST PAGE. 4 50 GENERAL DIRECTIONS FOR USE Below you will find the main steps to be taken for using your heater. For more details, please refer to the MANUAL (pages 53 ff. ). MAIN COMPONENTS OFF Button Knurled wick adjustment knob 1 2 Remove all packaging materials (refer to Section A, Fig. [. . . ] 7 Let the remaining fuel in the pump flow back into the jerrycan and carefully remove the pump. Carefully screw the fuel cap back on the tank using the empty full fuel cap cover. Close the lid. C IGNITING THE HEATER A new heater may give off some smells for a short while, when it is used for the first time. You should therefore provide extra ventilation or ignite the heater outside the living room. When you use the heater for the first time, first put the filled removable tank into place, and then wait approximately 30 minutes before you ignite the heater. Follow the same procedure when you have completely burnt up all fuel from the tank, and after the glass fibre wick has been replaced. Before igniting the heater, always check the fuel indicator to see whether the removable tank needs filling up (Green=full, Red=empty). Always ignite the heater with the knurled wick adjustment knob matches or a cigarette lighter. Never use K 1 Turn the knurled wick adjustment knob clockwise to its stop (Fig. If you apply more pressure you may turn it slightly further; however, it will automatically return to the start position. When you have set the wick to its highest position, this action will automatically activate the safety device. Reinstall the wick height lock (Section F). H MAINTENANCE Your heater needs hardly any maintenance. It is, however, important that you remove dust and stains in time with a damp cloth, because otherwise these may cause stains that are hard to remove. Follow the locally applicable regulations regarding the disposal of domestic chemical waste. THE WICK To extend the glass fibre wick life, you must occasionally let the heater burn until the tank is completely emptied and the heater extinguishes by itself. The burn-out will cause some smells, so it is recommended that you take the heater outside of the living room. Remove the removable tank from the heater and take out the fuel filter (Fig. Turn the fuel filter upside down and clean it from all dirt deposits by tapping it on a hard surface. (Never clean it with water!) Reposition the fuel filter in the heater. fuel filter P Do not remove any heater components yourself. Always contact your dealer for repairs. Let the heater cool down first, before you start any maintenance or service work. 4 57 I STORAGE (END OF THE HEATING SEASON) We recommend that you burn up all the fuel in the fuel tank at the end of the heating season and store the heater properly. Follow the procedure on the next page: 1 Ignite the heater outside the living room and let it burn until all fuel is used. 3 Clean the heater with a damp cloth and then dry it with a dry cloth. [. . . ] Should this happen, never try to move the heater, but always switch off the heater immediately (refer to Section E). In cases of emergency you may use a fire extinguisher, but only a type B extinguisher: a carbon dioxide or powder extinguisher. 10 TIPS FOR SAFE USE 100 cm 1 2 50 cm 20 cm 50 cm 150 cm 3 4 5 6 7 8 9 10 Make sure that children are always aware of the presence of a burning heater. Position the front of the heater at a minimum distance of 1. 5 metres from walls, curtains, and furniture. Make sure that the fuel is not exposed to heat or extreme temperature changes. [. . . ]