User manual ZIBRO SRE 186

[. . . ] For each model the minimum size of space is specified in which you can use the heater safely, without additional ventilation (refer to Section O). If a particular room is smaller than the specified space, always put a window or door slightly ajar ( 2. 5 cm). We also recommend doing this in highly insulated or draught-free rooms and/or at altitudes above 1, 500 metres. Do not use your heater in cellars or other underground areas. THE RIGHT FUEL Only the use of the correct fuel will ensure safe, efficient, and comfortable use of your heater. Only use Class C1 paraffin fuel in accordance with BS2869; Part 2, or equivalent. [. . . ] Never overfill the tank, especially not when the fuel is very cold (fuel expands when it heats up). empty full 7 Let the remaining fuel in the pump flow back into the jerrycan and carefully remove the pump. Clean off any spilled fuel. 8 Check whether the fuel cap is straight and tightened properly. Close the lid. C SETTING THE CLOCK It is only possible to set the correct time, when the heater is connected to the mains and not burning. First press either of the two keys to switch on the function (the 4-digit will start blinking). Next, set the hours using the key on the left (Nhour) and the minutes using the key on the right (Mmin. ). When you hold down the key, the value will continue going up, until you release the key E: When the 4-digit stops blinking, the setting has been locked to the indicated value. again. After approximately 10 seconds the 4-digit will stop blinking and the setting will be locked. 5 minutes after switching off the heater, the information on the display will disappear and the heater will automatically switch into the standby position. D F: The required temperature on the left, the measured temperature on the right. When the heater has been unplugged (or after a power failure), the time needs to be set again. IGNITING THE HEATER When used for the first time, a new heater may give out a smell for a short while. The POWER lamp will start blinking, indicating that the ignition procedure has started. The light next to them indicates that these numbers refer to the temperatures (Fig. The actual room temperature is indicated below ROOM, while the temperature setting is indicated below SET. When the burner is clean again, the heater will automatically switch back to the highest setting again. I CHILDPROOF LOCK The childproof lock can be used to prevent children accidentally changing the heater settings. When the heater is burning and the childproof lock is on, the heater can only be switched off. If the heater has already been switched off, the childproof lock also prevents accidental ignition of the H: When the mark appears, the childproof lock has been activated. heater. Activate the childproof lock by pressing the appropriate key down for more than 3 seconds. The KEY-LOCK indicator Switch off the childproof lock by pressing the key than 3 seconds once again. and holding it will appear on the information display (Fig. with a Fuel filter Regularly inspect the fuel filter as well: 1 Remove the removable tank L from the heater and remove the fuel filter (Fig. Some drops may leak from the filter; keep a cloth at hand. 2 Remove the dirt by tapping the fuel filter upside-down against a hard surface. (Never clean it with water!) 3 Reinstall the fuel filter into the heater. We recommend that you remove dust and stains from time to time with a damp cloth, because otherwise these may cause stains that are hard to remove. When the power cord is damaged, it may only be replaced by an authorised fitter. Use a new cord of the type H05 VV-F. 4 59 M STORAGE (END OF THE HEATING SEASON) At the end of the heating season, you must store the heater in a dust-free place, if possible in its original packaging. If there is still some fuel left, do not throw it away, but dispose of it in accordance with the local regulations for the disposal of domestic chemical waste. When you start re-using the heater follow the instructions again (starting from section A and as specified). M N TRANSPORTATION Take the following measures to avoid fuel leakage during the transportation of the heater: 1 Let the heater cool down. [. . . ] Do not use the heater in the immediate surrounding of a bath, a shower or a swimmingpool. Unplug the heater as well, when you go away for a longer period of time (e. g. Make sure that the fuel is not exposed to heat or extreme temperature changes. Always store the fuel in a cool, dry and dark place (sunlight will affect the quality). [. . . ]